Progress Lighting P400370 4-LT CHANDELIER
Package Contents
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Fixture | 1 |
| B | Canopy | 1 |
Hardware Contents (not actual size)
AA: Screw (#8-32) - Qty: 2 ?
BB: Wire nut - Qty: 3 ?
CC: Round mounting plate - Qty: 1 ⚙️
DD: Hex nut (#8-32) - Qty: 2 ?
EE: Cylinder nut - Qty: 2 ?
FF: 12" Pipe (1/8IP) - Qty: 4 ?
GG: 6" Pipe (1/8IP) - Qty: 1 ?
HH: Nipple (1/8IP) - Qty: 4 ?
Missing parts? Please contact Customer Service at 1-800-447-0573, 8am-8pm (Eastern), Monday - Friday, or at customerservice@progresslighting.com
Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs. ?
Preparation
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver ?, pliers ?, wire stripper ?, safety glasses ?, electrical tape ?, ladder ?.
Care and Maintenance
Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
Assembly Instructions
Step 1
Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust the screw length according to the fixture canopy depth.
Diagram Description: Shows the round mounting plate (CC) with screws (AA) and hex nuts (DD) threaded onto it. Arrows indicate adjustment of screws and nuts.
Step 2
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
Lift up the canopy (B) and pass the screws (AA) through the two mounting holes in the fixture canopy (B). While holding the canopy with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16" [5mm] of threads are showing. This length should be sufficient to mount the fixture.
Next, take the canopy down and go back and tighten the hex nuts (DD) up against the round mounting plate (CC) to secure the correct thread length for mounting the fixture.
Diagram Description: Shows the assembled mounting plate and screws being attached to an electrical box. Another diagram illustrates lifting the canopy (B) and passing screws (AA) through its holes, then threading them into the mounting plate (CC). A separate "INCORRECT / CORRECT" diagram shows the proper protrusion of screws (AA) from the mounting plate (CC) (approx. 3/16" or 5mm) for attachment to the outlet box.
Step 3
Equally adjust the arms by carefully turning them out from the center.
Diagram Description: Shows a central fixture body with multiple arms extending outwards. Arrows indicate rotating the arms to adjust their position.
Step 4
Note: During this step, determine the hanging length of your fixture by adding or removing stems (FF, GG, HH), optionally cutting the electrical and ground wire to length. Do NOT cut electrical wires or ground wires until this overall length is determined. Leave at LEAST 6 inches MINIMUM of wire past the canopy to allow for easy connections in step 5.
Pass the wires through the one pipe (GG), nipple (HH) and four pipes (FF), tightening the pipes to fixture (A) as you go to avoid twisting the wires. Secure tightly. Pass wires through the canopy (B) and secure the canopy tightly to pipes (FF).
Diagram Description: Shows the fixture (A) with wires being passed through various pipes (FF, GG, HH) and the canopy (B). Arrows indicate the direction of wire and pipe assembly. The canopy (B) is shown being secured to the pipes (FF).
Step 5
Strip 3/8" of insulation from the electrical wire ends.
Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box. Connect the SMOOTH fixture wire to the BLACK supply wire from the outlet box.
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate.
Push all wire connections into the outlet box.
Diagram Description: Shows the wiring connections inside the canopy. Two wire nuts (BB) are used to connect fixture wires (Ribbed and Smooth) to supply wires (White and Black). A ground wire connection is also shown, either with a wire nut or to a ground screw.
Step 6
Pass the screws (AA) through the two holes in the canopy (B). Secure the fixture to the screws (AA) using the two cylinder nuts (EE) provided. Tighten securely in place.
Diagram Description: Shows the canopy (B) with screws (AA) passing through it. Cylinder nuts (EE) are shown being threaded onto the screws (AA) to secure the fixture.
Step 7
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base lamp, SBCFL or SBLED. ?
Diagram Description: Shows the chandelier fixture with lamps being screwed into the sockets.
Warranty and Exclusive Remedy
Progress products, when properly installed and under normal conditions of use, are warranted to customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. Customers' sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Progress's sole and maximum liability for a defective product shall never exceed the cost of the subject product. EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS. Therefore, the customer's sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers. Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain customer's responsibility. Customer is responsible for determining the suitability of our products for customer's use or resale, or for incorporating them into objects or for applications which customer designs, assembles, constructs or manufactures.
