Progress Lighting P400311 4-LT Chandelier

Package Contents

Hardware Contents (not actual size)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION: Read instructions carefully and turn electricity off at main circuit breaker panel before beginning installation.

CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified electrician to ensure correct branch circuit conductor.

WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

Step 1: Prepare Mounting Plate

Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC) as shown. Adjust the screw length according to the fixture canopy depth.

Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.

Lift up the fixture and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16" [5mm] of threads are showing. This should be enough to mount the fixture.

Next, take the fixture down and tighten the hex nuts (DD) up against the mounting plate (CC). This ensures the correct length of threads for mounting the fixture.

Diagram Description: Shows attaching screws (AA) and hex nuts (DD) to the round mounting plate (CC). An illustration compares incorrect and correct screw length adjustment, indicating 3/16" [5mm] of thread should be visible for mounting.

Step 2: Adjust Hanging Length and Wire

Determine the desired hanging length by removing chain links (FF) and optional stems (HH/JJ/KK). Cut electrical and ground wires to length, ensuring AT LEAST 6 inches [15cm] of wire extends past the canopy loop (GG) for easy connections.

Diagram Description: Illustrates adjusting the chain length by opening and closing chain links (FF) with pliers. Wires are shown being routed through the chain and canopy loop (GG), stems (HH/JJ), and nipples (KK).

Open a chain link (FF) at one end and hook it onto the chain loop (GG). Close the link. Open the quick link (LL), attach the other end of the chain (FF) and the canopy loop (GG) to the quick link (LL), and close it.

Weave the wires through every third chain link (FF) and up through the canopy loop (GG).

Step 3: Connect Wires

Strip 3/8" [1cm] of insulation from the electrical wire ends.

Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box. Connect the SMOOTH fixture wire to the BLACK supply wire.

Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the round mounting plate.

Push all wire connections into the outlet box.

Diagram Description: Shows stripping wire ends and connecting the ribbed fixture wire to the white supply wire, and the smooth fixture wire to the black supply wire using wire nuts (BB). It also depicts connecting ground wires.

Step 4: Secure Fixture Canopy

Pass the screws (AA) through the two holes in the canopy (A). Secure the fixture to the screws (AA) using the two cylinder nuts (EE). Tighten securely.

Diagram Description: Illustrates passing screws (AA) through the fixture canopy (A) and securing them with cylinder nuts (EE).

Step 5: Attach Glass Shades and Install Bulbs

Attach the glass shade (B) to the fixture (A) using the socket ring (C) to secure it tightly.

Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base, SBCFL or SBLED bulbs.

Diagram Description: Shows attaching a glass shade (B) to the fixture (A) using a socket ring (C). It also indicates inserting light bulbs into the sockets.

Support and Contact Information

For questions regarding product information, assembly, or missing parts, please contact Progress Lighting:

Phone: 800-447-0573 (8am-8pm Eastern, Monday-Friday)

Email: customerservice@progresslighting.com

❓ Visit the Progress Lighting website for more information.

Warranty Information

Progress products are warranted to be free from defects in material and workmanship at time of shipment when properly installed and under normal use. Warranty claims must be asserted within one year from the date of purchase. The customer's sole remedy is limited to repair or replacement of the defective product. Progress's liability shall not exceed the cost of the product. All other warranties, express or implied, including warranties of merchantability and fitness for a particular purpose, are disclaimed. Progress is not liable for incidental or consequential damages. Customers are responsible for determining product suitability for their intended use.

Multilingual Notes

Safety warnings and wiring diagrams are also provided in French and Spanish on page 5 of the original document.