Baby Trend Snap-N-Go EX Universal Infant Car Seat Carrier

Warranty Information

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered or removed serial number, invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user.

Customer Service: 1 (800) 328-7363, Monday through Friday, 8:00 am - 4:30 pm PST.

Return Authorizations are required prior to returning product(s) to Baby Trend®. Warranty is valid only in North America.

(This document also contains warranty information in Spanish and French.)

Important Safety Warnings

[Warning] Please follow all instructions to ensure your child's safety. Keep these instructions for future reference.

[Warning] Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out; always use the safety harness and ensure children are properly positioned.

[Warning] Never leave children unattended.

[Warning] Care must be taken when folding and unfolding the stroller to prevent finger entrapment.

• Accessories like purses, shopping bags, parcels, or diaper bags may change the stroller's balance, causing a hazardous, unstable condition.
• Maximum weight capacity: Storage basket: 5 pounds (2.27 kg). Parent tray: 3 pounds (1.36 kg). Exceeding weight limits can cause instability.
• Ensure the stroller is completely opened and locked in place before allowing a child near it.
• Using the stroller with a total weight exceeding 45 pounds (20.36 kg) can cause excessive wear and stress, leading to instability.
• NEVER use the stroller on stairways or escalators.
• NEVER use the stroller with roller skates, in-line skates, skateboards, or bicycles.
• NEVER allow your stroller to be used as a toy.
• To clean, use only mild household soap or detergent and warm water on a sponge or clean cloth.
• Regularly check your stroller for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.
• Discontinue use if the stroller malfunctions or becomes damaged. Contact customer service for repair or replacement parts.

Parts Identification

Before assembly, verify you have all parts for this model.

• Parent Tray: The tray for the adult.
• Rear Wheel: The wheels located at the back of the stroller.
• Stroller: The main body of the stroller.
• Front Wheel: The wheels located at the front of the stroller.

[Diagram showing the Parent Tray, Rear Wheel, Stroller frame, and Front Wheel.]

Assembly Instructions

IMPORTANT: To ensure safe operation, follow these instructions carefully. Keep them for future reference.

IMPORTANT: Before assembly and each use, inspect the product for damaged hardware, loose joints, missing parts, or sharp edges. NEVER use if any parts are missing or broken.

IMPORTANT: Adult assembly is required.

Attaching Front Wheels

To attach the front wheels, unfold the stroller as described below:

1. Unfold the stroller frame by pulling upward and then backward on the stroller handle. [Illustration of stroller handle being pulled forward/backward].
2. Lean the stroller backwards so that it rests on the handle and rear frame tubes, with the front wheel bayonet pointing upward.
3. Position the front wheel assembly at the front wheel bayonet, ensuring the swivel assembly slides onto it. Push each front wheel assembly onto the bayonet until it snaps into place. [Illustration of front wheel assembly being attached].
4. NOTE: Pull on the wheel assembly to ensure it is securely attached.
5. (Continued in Spanish/French) Lean the stroller backward so it rests on the handle and rear frame tubes, and the front wheel bayonet points upward. Position the front wheel assembly onto the bayonet, allowing the swivel assembly to slide on. Push each front wheel assembly onto the bayonet until it snaps into place. [Illustration of front wheel assembly attachment].

Attaching Rear Wheels

Attach the rear wheels as follows:

2. Lean the stroller forward to rest on the front wheels. [Illustration of stroller tilted forward].
3. Position the rear axle and wheel assembly so the brake levers face the rear of the stroller. Press the rear wheel assembly onto the rear frame tubes, ensuring the push buttons on the forward side of each rear tube engage the hole on the forward side of each rear wheel housing. Pull on the rear wheel assembly to ensure it is securely attached. [Illustration of rear wheel attachment].
4. (Continued in Spanish/French) Press the rear wheel assembly into the rear frame tubes, ensuring the push buttons engage the hole on each rear wheel housing. Pull the rear wheel assembly to confirm it is securely attached. [Illustration of rear wheel attachment].

NOTE: NEVER use the stroller if wheels do not lock into place. For assistance, contact customer service at 1-800-328-7363 (M-F, 8 am - 4:30 pm PST).

Attaching Rear Basket

3. The rear basket tube needs to be installed prior to use. Insert the female end of the rear basket tube into the male ends located on the basket frame until it locks into place. [Illustration of rear basket tube connection].

Attaching Parent Tray

WARNING: Do not place hot liquids or more than 3 pounds in the parent tray. Serious burns or unstable conditions could result.

4. To attach the parent tray, position it so the hinges for the storage compartment face forward. Attach one end at a time by locating the fitting at the top of the frame and the hole on the side of the parent tray, then snap together. Repeat for the other side. Check that the tray is securely latched. [Illustration of parent tray attachment]. To remove, reverse the installation steps.

Engaging Brakes

WARNING: Always set brakes when the stroller is not being pushed to prevent it from rolling away. NEVER leave the stroller unattended on a hill or incline, as it may slide down.

5. To engage brakes, apply light downward pressure to the brake lever on each rear wheel. You may need to slightly move the stroller forward or backward to align the brake teeth with the wheel brake cluster. [Illustration of brake lever engagement].
6. Check that the stroller will not move and that both brakes are properly applied. To release, gently lift the brake lever.

Folding and Unfolding

To Fold Stroller

[Warning] Care must be taken when folding and unfolding to prevent finger entrapment.

[Caution] Do not allow children near the stroller while folding or unfolding.

1. To fold, slide the thumb trigger to the left and squeeze the pull trigger while pushing forward on the handle. [Illustration of folding trigger action].
2. Once the stroller begins to fold, release the handle and pull backward on the front frame until folded. Secure the stroller in the folded position by locking the fold latch, located on the side of the stroller, over the rivet that protrudes from the frame. [Illustration of folded stroller with latch].

To Unfold Stroller

7. Unlock the release lever. [Illustration of release lever].
8. Lift the stroller handle with both hands until the stroller frame is erect and locked in the open position. The stroller has spring-loaded latches on both sides. Test that both latches are fully engaged before placing your child in the stroller. [Illustration of unfolded stroller].

Infant Car Seat Attachment

[Warning] Avoid serious injury from falling or sliding out; always use the Infant Car Seat harness.

[Caution] Avoid serious injury from falling; always use the safety belt to secure the car seat to the stroller.

8. Place the car seat onto the upper frame. [Illustration of car seat placement].
9. Strap the safety belts over the car seat and connect the buckles. Tighten the strap so it fits snugly and the car seat is secured to the frame. Tighten the bottom support straps by pulling back on the loop and sliding the adjuster forward for a snug fit. [Illustrations of belt attachment and tightening].
10. NOTE: If your car seat has a belt path, feed the safety belt through it and secure.