Warranty Information
DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.
The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered/removed serial number, invalidates all claims against the manufacturer. Any property damage during installation is the sole responsibility of the end user.
Customer Service can be contacted at 1 (800) 328-7363, Monday through Friday, 8:00 am to 4:30 pm (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Warranty is valid only in North America.
(Information also available in Spanish and French)
Assembly Instructions
IMPORTANT: Adult assembly is required. Inspect product before assembly and each use for damaged hardware, loose joints, missing parts, or sharp edges. Never use if any parts are missing or broken.
Front Wheels Installation
To attach the front wheels, unfold stroller as described below:
1. Unlock the release lever, as illustrated in Figure 1a. Unfold stroller frame by pulling upward on the stroller handle until the frame locks, as shown in Figure 1b.
Lean the stroller backwards and push each front wheel assembly into the front wheel housing until they lock into place, as depicted in Figure 1c. NOTE: Pull on the wheel assembly to ensure it is securely attached. To remove for storage or maintenance, pull the lever on the bottom of the wheel and pull outward (refer to Figure 1c).
Rear Wheels Installation
2. Press the rear wheel posts into the rear frame hub until they click into place, as shown in Figure 2. NOTE: Pull on the rear wheels to ensure secure attachment.
Seat Attachment
3. Attach the seat by aligning the seat anchors on the side of the seat with the anchors on the stroller frame and pushing them together until they lock securely, as illustrated in Figure 3a. The seat can face forward or backward.
To take off the stroller seat, push both release buttons on each side of the seat anchors and lift the seat upwards, as shown in Figure 3b. NOTE: For the stroller seat only: DO NOT remove with child in the seat.
Seatback Positioning
4. To recline the seat: Squeeze the tabs on the adjuster and pull down while holding the strap loop, as shown in Figure 4a. To place the seat into an upright position, press upward on the adjuster with one hand while pulling the strap by the loop, as shown in Figure 4b. NOTE: The upright position should be used only for a child at least 6 months old. Always readjust the safety harness, including shoulder belts, when repositioning the seatback.
Child Tray
WARNING: The child's tray is not a restraint device; always secure your child with the seat belt. DO NOT lift the stroller by the child's tray. Use care when attaching the child's tray with a child in the stroller. Do not place hot liquids or more than 3 pounds (1.36 kg) in the child tray, as this could cause burns or instability.
5. To attach the child tray: Push the tray downward and onto each side of the front armrests until both side snaps lock into place, as illustrated in Figure 5a. Check that the tray is securely latched.
To access the child seat: Pull one side of the release lever, located on the underside of the child tray, as shown in Figure 5b, and lift upward. Either side of the child tray will lift and rotate out of the way to allow access to the front seat, as depicted in Figure 5c.
Canopy Operation
6. To open the canopy: Attach the hook and loop, as shown in Figure 6a. Push forward on the front edge of the canopy while holding the rear in place, as illustrated in Figure 6b. On the front edge, the visor can be folded in or out for additional shade. To fold the canopy: pull backwards on the front edge (refer to Figure 6b).
Brakes
WARNING: Always set brakes when the stroller is not being pushed to prevent it from rolling away. NEVER leave the stroller unattended on a hill or incline, as it may slide down.
7. To engage brakes: Apply downward pressure to the brake levers located on the rear axle, as shown in Figure 7. You may need to roll the stroller back and forth to fully engage the brake. NOTE: Check that the stroller does not move once the brakes are properly applied. To release: Gently lift up on the brake levers.
Securing the Child
WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness.
STRANGULATION HAZARD: Child can strangle in loose straps. Never leave child in seat when straps are loose or undone.
8. The 5-point harness shoulder straps have 3 attachment positions. Select the position that places the shoulder strap level with, or below, the child's shoulders, as illustrated in Figure 8a. To adjust harness height, unhook the shoulder strap from the crotch buckle. Feed the shoulder strap through the harness spread slots (accessed from the rear of the seat underneath the fabric). Feed shoulder strap through the appropriate slot and reattach to the crotch buckle.
Carefully place the child in the stroller seat. Bring the safety harness around the child's waist and over the child's shoulders. Place the crotch strap between the child's legs. Insert the male end of each shoulder/waist belt into the buckle on the crotch strap. Tighten the harness so it is snug around the child's waist and over the child's shoulders, as shown in Figure 8b.
Releasing the Child
9. To release the harness: Push the button on the center clasp, and the two harness buckles will pop free, as illustrated in Figure 9.
Sit N' Stand® Features
WARNING: The rear platform and jump seat are designed to accommodate a child who is at least 2 1/2 years old, has good balance and coordination, and is not over 40 inches tall.
STRANGULATION HAZARD! Children have strangled in loose straps. Never leave child unattended when straps are loose or undone.
10. Attach the Joy Ride Platform: Pull the locks back on the platform and attach it to the rear tube of the frame, as shown in Figure 10a. When the platform is not in use, remove it or rotate it upwards and secure it to the basket with the snap. NOTE: Make sure the platform locks onto the frame before use.
Jump Seat: Always use the 3-point harness while in the seated position facing the stroller handle. Put the seat belt around the child's waist and buckle to the crotch strap, as illustrated in Figure 10b. Adjust the seat belt to be snug around the child's waist.
Standing: Your child can stand on the riding platform facing forwards or backwards. NOTE: Use caution while standing on the platform. Make sure your child is always holding onto the frame while riding.
Folding and Unfolding
WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.
CAUTION: Do not allow children near the stroller while folding.
To Fold Stroller:
11. Pull the stroller backwards several inches to adjust the front wheels to the front, as shown in Figure 11a. Fold the stroller by sliding the fold lock with your thumb while squeezing the large fold button in the center of the handle and pushing forward on the handle, as illustrated in Figure 11b. Once the stroller begins to fold, release the handle and push forward until folded. Lock the release lever, as shown in Figure 11c. For a compact fold, place the seat on the stroller frame, as depicted in Figure 11d.
To Unfold Stroller:
CAUTION: Do not allow children near the stroller while unfolding.
12. Unlock the release lever, as shown in Figure 11c, and unfold stroller frame by pulling upward on the stroller handle until the frame locks, as illustrated in Figure 12.
Infant Car Seat Attachment
WARNING: Avoid serious injury from falling or sliding out; always use the Infant Car Seat harness.
13. Attach the car seat by lining up the seat anchors on the side of the car seat with the anchors on the stroller frame and push them together until they lock securely, as illustrated in Figure 13a. The car seat can face forward or backward.
To take off the infant car seat, push both release buttons on each side of the seat anchors and lift the car seat upwards, as shown in Figure 13b. INFANT CAR SEAT SOLD SEPARATELY.
To rotate the child tray: To attach an infant car seat, rotate the child tray to the vertical position. Press buttons on both sides to rotate down 90 degrees, as illustrated in Figure 13c.
Position the infant car seat facing toward the rear of the stroller so the seat shell goes into the child tray and latches into place, as depicted in Figure 13d.
When the infant car seat is seated firmly, strap the short clip over the infant car seat through the seat belt slots and pull the strap adjuster tight, as shown in Figure 13e. NOTE: It is very important that the short clip is always tightly fastened around the infant car seat.
For the Ally infant car seat, be sure to use the additional support strap located on the back side of the stroller seat frame, as illustrated in Figure 13f.
Universal Car Seat Adapter
14. Compatible with the Universal Car Seat Adapter (sold separately).
Universal Infant Car Seat Carrier: Accepts all Baby Trend® and most major brands of Infant Car Seats. Visit www.babytrend.com.
Compatible with most Baby Trend® modular strollers and joggers (MUV®, Snap Tech, Snap Gear®, Snap Fit™) and transforms them into infant car seat carriers.
Care and Maintenance
15. Seat Pad: To clean the seat pad, use only mild household soap or detergent and warm water on a sponge or clean cloth.
Other: Regularly check your stroller for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed.
