Baby Trend Snap-N-Go Double Stroller
Baby Trend, Inc.
13048 Valley Blvd.
Fontana CA 92335
Customer Service: 1-800-328-7363 (8:00am - 4:30pm PST)
Website: www.babytrend.com
Warranty Information
Do not return your product to the store. Please contact Baby Trend for replacement parts, service, and repair.
The Baby Trend® warranty covers workmanship defects within the first 180 days of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered or removed serial number, invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user.
Warranty is valid only in North America.
General Instructions
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Safety Warnings and Precautions
WARNING: Please follow all instructions to ensure your child's safety. Keep these instructions for future reference.
WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out; always use the safety harness and ensure children are properly positioned.
WARNING: Never leave children unattended.
WARNING: Care must be taken when folding and unfolding the stroller to prevent finger entrapment.
- Purses, shopping bags, parcels, diaper bags, or accessory items may change the stroller's balance, causing a hazardous, unstable condition.
- Maximum weight in storage basket: 7 pounds (3.17 kg). Maximum weight on parent tray: 3 pounds (1.36 kg). Exceeding weight limits can cause hazardous unstable conditions.
- Ensure the stroller is completely opened and locked before allowing a child near it.
- For use with two infant car seats (including infant), weighing no more than 45 pounds (20.4 kg) each, or a total weight of no more than 90 pounds (40.82 kg) combined. Exceeding weight limits will cause excessive wear and stress, potentially leading to a hazardous, unstable condition.
- This product is designed for two infant car seats and two infants. NEVER use with only one infant car seat.
- NEVER use the stroller on stairways or escalators.
- NEVER use the stroller with roller skates, in-line skates, skateboards, or bicycles.
- NEVER allow your stroller to be used as a toy.
Cleaning: Use mild household soap or detergent and warm water on a sponge or clean cloth.
Maintenance: Regularly check your stroller for loose screws, worn parts, torn material, or stitching. Replace or repair parts as needed. Discontinue use if the stroller malfunctions or becomes damaged. Contact customer service for repair or replacement parts.
Parts Identification
A diagram shows the Baby Trend Snap-N-Go Double stroller, a double infant car seat carrier.
- Stroller
- Parent Tray (Bandeja para padres / Plateau pour adulte)
- Rear Wheel (Rueda trasera / Roue arrière)
- Front Wheel (Rueda delantera / Roue avant)
Assembly Instructions
IMPORTANT! To ensure safe operation, follow these instructions carefully. Inspect the product for damaged hardware, loose joints, missing parts, or sharp edges before assembly and each use. NEVER use if parts are missing or broken. Adult assembly is required.
Remove the stroller from the box. The front wheels, rear wheels, and parent tray MUST be installed prior to use.
Unfolding the Stroller
- Pull the stroller frame upward and then backward on the stroller handle to unfold. (Diagram description: Figure 1 shows the stroller frame being pulled upward and backward.)
- Extend the front frame by rotating it forward. Slide the two plastic fittings forward and then back so that both latch securely onto the front tubes of the stroller frame. (Diagram description: Figure 2a shows the front frame rotating forward. Figure 2b shows the plastic fittings latching onto the front tubes.)
Attaching Front Wheels
- Lean the stroller backward so that it rests on the handle and rear frame tubes, with the front wheel bayonet pointing upward. Position the front wheel assembly at the front wheel bayonet and push until it snaps into place. (Diagram description: Figure 3 illustrates leaning the stroller backward and attaching the front wheel assembly.)
NOTE: Pull on the wheel assembly to ensure it is securely attached.
Attaching Rear Wheels
- Lean the stroller forward to rest on the front wheels. Position the rear axle and wheel assembly with brake levers facing the rear. Press the rear wheel assembly onto the rear frame tubes, ensuring the push buttons on the forward side of each rear tube engage the hole on the forward side of each rear wheel housing. (Diagram description: Figure 4 illustrates leaning the stroller forward and attaching the rear wheel assembly.)
NOTE: Pull on the rear wheel assembly to ensure it is securely attached.
Assistance: If wheels do not lock into place, contact customer service at 1-800-328-7363, Monday-Friday, between 8 am and 4:30 pm PST.
Attaching Basket
- Install the rear basket tube by inserting the female end into the male ends located on the basket frame until it locks into place. (Diagram description: Figure 5 shows the rear basket tube being inserted into the basket frame.)
Attaching Parent Tray
- Position the parent tray so that the hinges for the storage compartment are facing forward. Snap the parent tray to the stand at the top of the frame. (Diagram description: Figure 6 shows the parent tray being attached to the stroller frame.)
NOTE: Check that the tray is securely latched. To remove the parent tray, reverse the installation steps.
Brake Operation
- To engage brakes, apply light downward pressure to the brake lever on each rear wheel. The stroller may require slight forward or rearward movement to align the teeth on the brake with each wheel brake cluster. (Diagram description: Figure 7 illustrates applying pressure to the brake lever on the rear wheel.)
NOTE: Check that the stroller will not move and that both brakes are properly applied.
To release, gently lift up on the brake lever.
Folding the Stroller
- Fold the front section back to reduce the folded size of the stroller. To fold the front frame, slide the plastic fitting forward then lift upward on the frame. Rotate the front frame backward and rest on the rear portion of the frame. (Diagram description: Figure 8a shows the front frame being slid and lifted. Figure 8b shows the front frame rotated backward.)
- Slide the thumb trigger to the left and squeeze the pull trigger while pushing forward on the handle. (Diagram description: Figure 8c shows the thumb trigger and pull trigger being used to fold the stroller.)
- Once the stroller begins to fold, release the handle and pull backward on the front frame until the stroller is folded. Secure the stroller in the folded position by locking the fold latch, located on the side of the stroller, over the frame rivet. (Diagram description: Figure 8d shows the fold latch securing the folded stroller.)
Unfolding the Stroller
- Unlock the release lever. (Diagram description: Figure 9a shows unlocking the release lever.)
- Lift the stroller handle with both hands until the stroller frame is erect and locked in the open position. The stroller has spring-loaded latches on both sides of the frame. (Diagram description: Figure 9b shows the stroller frame being lifted to the open and locked position.)
NOTE: Test that both latches are fully engaged prior to placing your child in the stroller.
Extend the front frame by rotating it forward. Slide the two plastic fittings forward and then back so that both latch securely onto the front tubes of the stroller frame.
Infant Car Seat Attachment
WARNING: Avoid serious injury from falling or sliding out; always use the Infant Car Seat harness.
CAUTION: Avoid serious injury from falling; always use the safety belt to secure the car seat to the stroller.
Attaching Car Seats
- Place car seats onto the upper frame. (Diagram description: Figure 10a shows car seats being placed on the upper frame.)
- Strap the safety belts over the car seats and connect the buckles together. Tighten the strap so it fits snugly and the car seat is secured to the frame. Tighten the bottom support straps, located on the back of the upper frame, by pulling back on the loop and sliding the adjuster forward for a snug fit. (Diagram description: Figure 10b shows safety belts being strapped over the car seats and buckled. Figure 10c shows the bottom support straps being tightened.)
NOTE: Some car seats have a belt path for the safety belt to slide through. If you have a car seat with a belt path, please feed the safety belt through it and secure.
