Z-07ZI6JVU-4527 Pendant Light Installation Guide

Important Safety Information

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. Installation by a licensed electrician is suggested.

2. Please read these instructions carefully and save them for future reference.

3. Before starting, NEVER attempt any electrical work without shutting off the electricity.▶️ Go to the main fuse or circuit breaker box in your home and place the main power switch in the “OFF” position.▶️ Place the wall switch in the “OFF” position.

4. The mounting surface should be clean, dry, flat, strong enough, and at least 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16" should be corrected as required.

5. Ensure the ceiling or wall can support the weight of the lamp before installation.

6. Verify your voltage is 120V. The maximum wattage per bulb is 40W.

7. Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp's surface.

8. When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs get hot quickly.

9. The safety instructions in this manual are not exhaustive and may not cover all possible conditions. Common sense, caution, and care must be used with any electrical products.

Illustration showing the finished pendant light fixture.

Tools Required (Not Included)

Before starting assembly and installation, please prepare the needed tools:

• Ladder
• Phillips head/flat blade screwdriver
• Electrical tape
• Pliers
• Wire cutter/Stripper

Parts and Accessories

Parts Type & QTY Including:

• (A) Mounting plate assembly (1)
• (B) Green ground screw (1)
• (E) Canopy (1)
• (F) Strain relief (2)
• (G) Ball knob (2)
• (H) Cord (1)
• (I) Stem (1)
• (J) Cover (1)
• (K) Socket (1)
• (L) Glass shade (1)

Accessories & QTY Enclosed:

• (C) Plastic Wire Connector (3)
• (D) Mounting screw (2)
• (M) Allen wrench (1)

Assembly & Installation Instructions

Step 1: Unpack and Inspect

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.

Step 2: Turn Off Power

Before starting the installation, NEVER attempt any work without shutting off the electricity until the work is done.

▶️ Go to the main fuse or circuit breaker box in your home. Place the main power switch in the “OFF” position.

▶️ Place the wall switch in the “OFF” position.

Step 3: Prepare Mounting Plate

Unscrew ball knobs (G) from canopy (E) then gently remove mounting plate assembly (A).

Diagram showing the canopy (E) with ball knobs (G) being removed, and the mounting plate assembly (A) detached.

Step 4: Adjust Cord Length

Adjust the length of cord (H) to achieve the desired height of the mounted fixture.

1. Use Allen wrench (M) to unscrew the screw in strain relief (F). Carefully pull and push cord (H) through canopy (E) and strain relief (F) to lengthen or shorten the length of cord (H).

2. Once the desired height is achieved, carefully tighten the screw till snug.

NOTE: To prevent cord (H) from slipping out of canopy (E), make an overhand knot of cord (H).

Diagram illustrating the process of adjusting the cord (H) length using the Allen wrench (M) and strain relief (F) on the canopy (E).

Step 5: Prepare Fixture Wires

If needed, shorten the extra length of the fixture wires from cord (H) so that they are all at least 6 inches (152.4 mm) long above canopy (E) within the outlet box.

Step 6: Mount the Fixture Plate

Carefully pass supply wires through mounting plate assembly (A). Secure mounting plate assembly (A) to the outlet box with mounting screws (D).

NOTE: The side of mounting plate (A) marked "GND" must face out.

Diagram showing the mounting plate assembly (A) being attached to the outlet box using mounting screws (D), with the "GND" marking oriented outwards.

Step 7: Make Wire Connections

Connect wires as shown in the following charts. NEVER connect other wires to ground wires.

Connect Ground Wires:

Diagram illustrating ground wire connections: Outlet box ground wire connects to the green ground screw on the mounting plate assembly (A), and the fixture ground wire connects to the same green ground screw, often with a washer and screw.

Connect Supply Wires:

Note: When parallel wires (SPT I & SPT II) are used, the neutral wire is square shaped or ridged, and the other wire will be round or smooth.

Diagram showing the connection of fixture wires to supply wires, matching colors and types as per the chart.

Step 8: Secure the Canopy

Fix canopy (E) to mounting plate assembly (A) and secure with the previously removed ball knobs (G).

Note: Canopy (E) should be snug against the ceiling and ball knobs (G). If not, adjust the threaded length of the pre-assembled mounting screws on mounting plate assembly (A):▶️ First, unscrew the pre-assembled hex nuts.▶️ Then, screw the pre-assembled mounting screws in or out of mounting plate (A).▶️ When the secure length is achieved, tighten the pre-assembled hex nuts and return to step 8.

Diagram showing the canopy (E) being attached to the mounting plate assembly (A) and secured with ball knobs (G), with an inset showing the adjustment mechanism for mounting screws.

Step 9: Install Stem, Bulb, and Shade

1. Screw stem (I) onto the top of cover (J).

2. Install the bulb (Not included). Please do not exceed the maximum wattage recommended on the socket.

3. Carefully screw glass shade (L) onto socket (K).

Diagram illustrating the final assembly steps: screwing the stem (I) onto the cover (J), inserting the bulb (not shown), and attaching the glass shade (L) to the socket (K).

Step 10: Final Check and Power On

Check that everything is installed properly, then you can turn on the light. Enjoy!

Ordering Parts

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use the exact wording from the illustration when ordering parts.

Cleaning

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.