JA-110P PET - Bus PIR Motion Detector with Basic Pet Immunity
This document has been machine translated from the original English version. For any ambiguities or doubts, please refer to the original version of the document. For errors or further questions, please contact Technical Support (contact details are at the end of this document).
The JA-110P PET is a bus device of the JABLOTRON system. It is used for detecting human movement in buildings. Unlike the standard PIR motion detectors of the JABLOTRON series, this detector features a modified detection characteristic and is equipped with basic pet immunity. The detector eliminates the effects of small animals moving on the floor (up to approx. 25 kg and a maximum size of 40 cm). The detector reacts impulsively and takes a position in the system. The installation of the detector should be carried out by a trained technician with a valid certificate from an authorized dealer.
Installation
⚠️ Always switch off the system's power supply when connecting the detector to the bus.
- Open the detector cover by pressing the latch (5). Do not touch the PIR sensor inside (11) as it could be damaged.
- Remove the circuit board – it is held by a latch (3).
- Punch holes for screws and cables in the plastic base. The recommended mounting height for the detector is 2 m above the floor.
- Insert the bus cable and fix the plastic base to the wall with screws (vertically, with the cover latch facing downwards).
- Reinsert the circuit board and connect the cables to the terminals (8).
- Proceed by following the installation manual of the control panel.
Fig. 1: Opening the detector and description of the product's internal and external parts.
Internal and External Parts:
- 1 – Holes for mounting on a flat wall
- 2 – Holes for angled mounting (in a corner)
- 3 – Circuit board latch
- 4 – Holes for angled mounting (in a corner)
- 5 – Cover latch
- 6 – Red LED – Activation
- 7 – Yellow LED – Fault
- 8 – Bus terminals
- 9 – Production code
- 10 – Cover tamper sensor
- 11 – PIR sensor
System Assignment and Settings
Depending on the control panel type, use the recommended software or application (see the control panel manual).
Technical Data
| Feature | Value | Feature | Value |
|---|---|---|---|
| Power | from the central bus 12 V (8...15 V) | Operating environment | Indoor general |
| Quiescent current consumption | 5 mA | Operating temperature range | -10 °C to +40 °C |
| Maximum current consumption | 10 mA | Average operating humidity | 75% relative humidity, non-condensing |
| Recommended installation height | 2 m above the floor | Certification body | Trezor Test sro (No. 3025), KIWA Nederland bv |
| Detection angle/detection range | 90°/12 m | Also complies with | EN 50131-1, EN 50131-2-2, EN 50130-4, EN 55032, EN IEC 63000, T 031. |
| Detection angle/detection range – pet immunity | 90°/7 m | Recommended screw | 2x Ø 3.5 x 40 mm (countersunk head) |
| Dimensions | 60 x 98 x 52 mm | Weight | 75 g |
| Classification | Class 2/II. Indoor general (According to EN 50131-1) |
Conformity and Disposal
JABLOTRON a.s. hereby declares that the JA-110P PET, when used as intended, complies with the relevant harmonization legislative provisions of the European Union (Directives No. 2014/30/EU and 2011/65/EU). The original Declaration of Conformity can be found at www.jablotron.com in the Downloads section.
Disposal Note: By properly disposing of this product, you save valuable resources and avoid potential negative impacts on health and the environment that may result from improper disposal. Please return the product to your dealer or contact your local authority for more information on the nearest collection point.
For an electronic version of this document (available in other languages) or a version for mounting in JA-100, scan the enclosed QR code.
