2000-Up Hyundai Tiburon 2-Door Sports Coupe Car Audio Installation Guide
General Chassis and Unit Dimensions
The following table outlines dimensions for various head unit types and their corresponding chassis requirements. Dimensions are in inches.
| Unit Type | Chassis Height | Chassis Width | Chassis Depth | Nose Height | Nose Width | Shaft Spacing |
|---|---|---|---|---|---|---|
| MINI | 1 3/4-2 | 7 1/8 | 4 3/4-5 1/2 | 1 5/8-1 3/4 | 4 1/8-4 3/16 | 5 1/8-5 3/4 |
| STAN | 2 | 7 1/8 | 5 7/8-6 | 1 11/16 | 4 1/8-4 3/16 | 5 1/8-6 |
| DIN | 2 | 7 1/8 | 5 7/8-6 | 1 11/16 | 7 1/2 | |
| ISO DIN | 2 | 7 | 5 7/8-6 | 1 11/16 | 6 11/16 | |
| SINGLE DBL DIN | 3 7/8 | 7 1/8 | 5 7/8-6 | 3 3/4-4 | 6 11/16-7 1/4 | |
| RADIO EQ STACK | 3 | 7 1/8 | 5 7/8-6 | 1 11/16 |
In-Dash Application Notes
The following table indicates required kits or modifications for specific vehicle years and models.
| Vehicle Year | 2000 | 2001 | 2002 | 2003 | 2004 | 2005 |
|---|---|---|---|---|---|---|
| Hyundai Tiburon | K | K | K | K4 | F2 | K |
Application Kit Model: HY1602
Harness Adaptor: HY04
In-Dash Installation Area Dimensions
| Area | Depth | Max Depth | Width | Height |
|---|---|---|---|---|
| Cavity | 7 15/16" | 7 15/16" | 7 1/4" | 4 5/16" |
| Dash Opening | Type: Double DIN | |||
| Dash Material | Plastic | |||
| For Max Depth | Remove Rear Support, Modify Cavity | |||
Amplifier/EQ Mounting Locations (WxHxD)
| Under/In Dash | Under Seat | Glove Box | Trunk/Cargo |
|---|---|---|---|
| 14 1/4" x 2" x 13" | 11 1/4" x 6" x 6" | Various |
Vehicle Specific Installation Notes: Hyundai Tiburon (2000-Up)
Dashboard: Factory provisions include a 1" 2-hole tweeter. Aftermarket installations may require specific kits.
Antenna: The factory antenna is located on the top of the driver's side rear quarter panel.
Speaker Installation Details
Dash Speaker
Factory Provision: 1" tweeter mounted on the backside of the front pillar panel.
Front Door Speaker
Factory Provision: 6 1/2" speaker mounted in a factory speaker adapter.
Aftermarket Fitment: 5 1/4" or 6 1/2" speakers require a speaker adapter. Recommended adapters: Scosche SAC656 or SAU56.
Installation Steps:
- Extract seven Phillips head screws from the door panel perimeter.
- Extract one Phillips head screw from the door opener cup and remove.
- Using a small pick, remove two plastic Phillips head screw covers from the door handle and extract two Phillips head screws from behind.
- Use a panel removal tool to remove the plastic side mirror triangle.
- Using a panel removal tool, unsnap the door panel perimeter, lift away, unplug, and remove.
- Extract four Phillips head screws from the speaker, disconnect, and remove.
Rear Deck Speaker
Factory Provision: 6 x 9" speaker mounted in the rear deck.
Aftermarket Fitment: 5 1/4" or 6 1/2" speakers require a speaker adapter. Recommended adapter: Scosche SA69.
Installation Steps:
- Unsnap grill using a panel tool from the top and remove.
- Extract four Phillips head screws from the speaker, disconnect, and remove.
Modification Key
- B: Back up plates required.
- C1: Cut trim/plastic (structure).
- C2: Cut steel.
- D: Below deck only.
- D1: Lift portion of deck (may require structural reinforcement).
- D2: Cut steel when top mounted; do not if below deck.
- D3: Narrow surface, below deck only.
- F2: Modify dash cavity and/or panel.
- K: Installation kit, spacer, or adapter required.
- K4: Fabricate panel/brackets.
- K5: When equipped with standard two shaft radio/tape player. Fabricate kit when equipped with flat face electronic radio/tape player.
- KS: Scosche kit recommended.
- N: Not recommended; extensive modification required.
- P: Perfect without modification.
- P1: Modify or remove pockets.
- P2: Coin pocket location in dash (may require trim kit).
- P3: Perfect when equipped with standard two shaft radio; K without.
- R: Rear load isomoount.
- U: Underdash.
- W1: With power windows only.
- W2: Without power windows only.
