1999-2003 Daewoo Leganza Car Audio Installation Guide
Scosche Installation Information
This document provides specifications and installation guidance for upgrading the car audio system in the 1999-2003 Daewoo Leganza models.
Vehicle Specifications
Year: 1999-2003
Make: Daewoo
Model: Leganza
Image of a 1999-2003 Daewoo Leganza car.
In-Dash Application
Dash Type: Double DIN
Recommended Kit: DO2110
Harness: DO01
Antenna Adapter: Not Needed
CD Changer Interface: None
Speaker Fitment
Front Speakers
- Dash: 1½" speaker, 1" mounting depth.
- Front Door: 7" 4-Hole speaker, 3 1/16" mounting depth.
For aftermarket 5 ¼" or 6 ½" speakers, a speaker adapter is required. Scosche recommends the SAC656 speaker adapter.
Image showing the car's dashboard with the factory stereo area.
Rear Speakers
- Rear Door: 6 x 9" 4-Hole speaker, 20" mounting depth.
For aftermarket 5 ¼" or 6 ½" speakers, a speaker adapter is required. Scosche recommends the SA69 speaker adapter.
Image of a front door speaker installation point.
Image of the rear deck speaker mounting area.
Wire Color Codes
| Wire Function | Color Code |
|---|---|
| +12V Constant | Orange |
| +12V Accessory Switched | Yellow |
| -12V Chassis Ground | Black |
| +12V Illumination | Brown/White |
| Power Antenna | Gray |
| LF+ (Left Front Positive) | Brown/White |
| LF- (Left Front Negative) | Gray |
| RF+ (Right Front Positive) | Light Green |
| RF- (Right Front Negative) | Dark Green/White |
| LR+ (Left Rear Positive) | Brown |
| LR- (Left Rear Negative) | Yellow |
| RR+ (Right Rear Positive) | Dark Blue |
| RR- (Right Rear Negative) | Light Blue |
Installation Procedures
Preliminary Steps
Disconnect the negative battery cable before beginning installation.
Antenna Location
The factory antenna is located atop the driver's side rear fender.
Radio Removal and In-Dash Installation
Note: The factory stereo provision is for a Double DIN size radio.
- Using a small angled pick, carefully pull on the far corners of the radio bezel.
- Extract 4 Phillips head screws holding the radio.
- Disconnect and remove the factory radio.
Front Door Speaker Removal and Installation
Note: The factory speaker provision is for a 7" 4-Hole speaker mounted in a factory speaker adapter, and a 1½" tweeter. When installing an aftermarket 5 ¼" or 6 ½" speaker, a speaker adapter is required.
Driver Side Speaker
- Extract 5 Phillips head screws from the perimeter of the door panel.
- Extract 1 Phillips head screw from the door grabber cup.
- Use a small pick to release the door cup at the locking mechanism, top and bottom off the door opener.
- Carefully lift upwards on the door panel.
- Extract 4 Phillips head screws from the speaker, disconnect, and remove the speaker.
Tweeter
- Using a small pick, release the left and right side by pressing inwards and lifting up.
- Disconnect and remove the tweeter.
Rear Deck Speaker Removal and Installation
Note: The factory speaker provision is for a 6 x 9" 4-Hole speaker. When installing an aftermarket 5 ¼" or 6 ½" speaker, a speaker adapter is required.
- Using a panel removal tool, extract 3 plastic fasteners from the rear deck.
- Disconnect the third brake light and extract 2 x 8 mm nuts holding it in place.
- Use your knee to release the bottom seat cushion.
- Remove the entire seat assembly.
- Lift upwards and out on the rear deck.
- Extract 4 Phillips head screws from the speaker, disconnect, and remove the speaker.
Important Notes
This manual is based on carefully documented research. Absolute accuracy is attempted but not guaranteed. Use this manual as a reference guide. Scosche, Inc. cannot be responsible for inconsistencies that may occur.
© 2000 Scosche Industries, Inc. All rights reserved.
For more information visit www.scosche.com or call Scosche Industries, Inc. at 800-363-4490.
