HOMCOM 839-651V00 TV Stand Assembly Instructions

Model: 839-651V00

Product Overview

This document provides assembly instructions for the HOMCOM TV stand, model 839-651V00. The assembly is estimated to take approximately ⏰ 60 minutes and involves 8️⃣ steps.

Important: Retain for future reference. Read carefully.

General Assembly Notes

Quickfit Mechanism

When using the Quickfit mechanism, tighten it until the shoulder is flush with the panel. Avoid overtightening or undertightening.

Cam Lock Mechanism

Before inserting the connecting quickfit, ensure the cam lock is in the correct starting position.

Panel Joining

When joining two panels, the head of the quickfit should be centered within the cam lock. The cam lock must be inserted before the quickfit.

Tightening Cam Locks

To tighten a cam lock, turn it clockwise.

Hinge Adjustment

Adjustments to the hinges may be necessary to ensure doors are properly aligned. Follow the instructions below:

Vertical Door Adjustment

To adjust the door vertically, loosen the screw as shown ? and move the door up or down as needed.

Door Gap Adjustment

To adjust the gap between the door and the main frame, turn the screw clockwise or anti-clockwise as required.

Lateral Door Adjustment

To adjust the door laterally, turn the screw as shown ? clockwise or anti-clockwise.

Final Fastening

Ensure all other screws are securely fastened.

Example Assembly Step (A1)

This section illustrates the use of hardware 'A1' (likely a screw or bolt). Step 01 shows a spare plastic hardware piece being tapped into a panel with a hammer ?. Step 02 shows hardware 'A1' being screwed into a panel.

✔️ Correct installation shown. ❌ Incorrect installation shown.

Parts List

• Part 1: Rectangular panel (x1)
• Part 2: Rectangular panel with holes (x1)
• Part 3: Long, thin rectangular panel (x1)
• Part 4: Long, thin rectangular panel (x1)
• Part 5: Rectangular panel with holes (x1)
• Part 6: Short, thin rectangular panel (x2)
• Part 7: Long, thin rectangular panel (x2)
• Part 8: Rectangular panel with a large hole (x1)
• Part 9: Rectangular panel with a large hole (x1)

Hardware List

• A: Screw (M3.5*14), x16 (+2 spare)
• B: Screw (M8*30), x14 (+2 spare)
• C: Screw (M3.5*14), x24 (+2 spare)
• D: Screw (M3.5*28), x6 (+2 spare)
• E: Cam lock mechanism, x4
• F: Cable management clip/holder, x1
• G: Dowel/pin, x3
• H: Allen key/wrench, x6
• I: Small cylindrical piece (e.g., cap or cover), x8
• J: Screw, x4
• K: Round plastic piece (e.g., foot or cap), x16 (+2 spare)
• Spare plastic hardware: x4

Assembly Steps

Step 01

Attach panels 3, 4, and 6 to the base panel 1 using hardware A, B, J, and F. Panel 1 is the base. Panels 3 and 4 are attached to the base with screws A and J. Panel 6 pieces are also attached.

Step 02

Attach panels 2 and 5 to the structure from Step 01 using hardware A. This forms the main sides and back supports of the cabinet.

Step 03

Attach panels 8 and 9 to the structure using hardware A. These panels likely serve as internal dividers or back panels, completing the main cabinet box.

Step 04

Install internal components or supports using hardware D, G, and H. This step involves securing internal elements, possibly using dowels (G) and screws (D) tightened with the Allen key (H).

Step 05

Attach hinges (E) and other hardware (C) to the cabinet doors (parts 7) and the main frame. This prepares the doors for mounting.

Step 06

Mount the doors (parts 6 and 7) to the cabinet structure using hardware A and K. This step attaches the doors to the main body.

Step 07

Finalize connections and reinforce the structure, potentially using hardware I. The cabinet with doors attached is shown.

Step 08

Assembly is complete. ✔️

Support and Contact Information

For any questions or assistance regarding the assembly or use of this product, please contact the customer care center. Contact details for various regions (US, CA, DE, IT, ES, UK, FR, PT) are provided in the original document. Information regarding the recycling of the product and its accessories is also available.