Bosch Dishwasher SMH4EVX08E: Quick Start Guide
Home Connect Setup
Connect your appliance to a mobile device for convenient settings management via the Home Connect app.
Scan the following QR code to install the Home Connect app and connect your appliance.
[QR code for Home Connect app download and device connection]
Follow the instructions in the Home Connect app.
Water Hardness Settings Overview
This section provides an overview of the adjustable water hardness levels.
| Water Hardness Range (mmol/l) | Setting Value |
|---|---|
| Soft: 0 - 1.1 | H00 |
| Soft-Medium: 1.2 - 1.4 | H01 |
| Medium: 1.5 - 1.8 | H02 |
| Medium: 1.9 - 2.1 | H03 |
| Medium: 2.2 - 2.9 | H04 |
| Hard: 3.0 - 3.7 | H05 |
| Hard: 3.8 - 5.4 | H06 |
| Hard: 5.5 - 8.9 | H07 |
Adjusting the Water Softener
- Press [button].
- To open basic settings, press [Setup button] for 3 seconds. The display shows Hxx. The display shows set.
- Press [Start button] until the correct water hardness level is set.
- To save settings, press [Setup button] for 3 seconds.
Adding Special Salt
To prevent appliance damage, only add special salt to the designated reservoir just before starting a program.
- Unscrew and remove the cap of the special salt reservoir.
- For first-time use: completely fill the reservoir with water.
- Pour special salt into the reservoir. The water in the reservoir will overflow and drain. Never add detergent.
- Replace and close the reservoir cap.
[Diagram showing how to open the salt reservoir, fill with water (if first use), add salt, and close the cap.]
Adding Rinse Aid
- Press the catch on the rinse aid reservoir lid and lift it [arrow pointing up symbol].
- Add rinse aid up to the [max marking].
- Close the rinse aid reservoir lid. The lid locks with an audible click.
[Diagram showing how to open the rinse aid compartment, fill to the max line, and close the lid.]
Programs Overview
Program data are laboratory values according to European standard EN 60436. Consumption values are indicative (except Eco) and depend on the selected program and additional function. The running time changes if the rinse aid system is deactivated or if there is no rinse aid.
| Program | Duration [h:min] | Energy Consumption [kWh] | Water [l] |
|---|---|---|---|
| Intensive 70° | 2:05 - 2:15 | 1.350 - 1.400 | 10.5 - 13.5 |
| Auto 45-65° | 1:40 - 2:45 | 0.850 - 1.450 | 7.0 - 15.5 |
| Eco 50° | 3:55 | 0.645 | 9.0 |
| Silent 50° | 4:00 | 1.100 | 10.5 |
| Express 65° - 1h | 1:00 | 1.200 | 10.0 |
| Appliance Care | 2:10 | 1.350 | 15.1 |
| Favourite | 0:15 - 0:15 | 0.050 - 0.050 | 4.0 - 4.0 |
1 Silent program: Extended running time, therefore very quiet.
Adding Detergent
- Pour detergent into the dry detergent compartment.
- Close the detergent compartment lid. The lid locks with an audible click.
[Diagram showing how to open the detergent compartment, add detergent, and close the lid.]
Operating the Dishwasher
- Load the dishes. Only wash dishwasher-safe items. Remove coarse food residue from dishes. Ensure the spray arms can rotate freely.
- Add detergent.
- Switch on the appliance [power symbol].
- Set the program.
- Start the program [play symbol].
- At the end of the program, unload the dishes.
- To interrupt the program, press and hold the [Reset button] for approx. 4 seconds. The program will be interrupted and will end after approx. 1 minute.
Cleaning and Maintenance
Cleaning the Filters
- After each wash, check the filters for residues.
- Rotate the coarse filter anti-clockwise and remove the filter system [filter-removal symbol].
- Remove the microfilter by pulling it downwards.
- Press the retaining tabs and pull the coarse filter upwards [arrow pointing up symbol].
- Wash the filter elements under running water.
- Reassemble the filter system.
- Insert the filter system into the appliance and rotate the coarse filter clockwise. Ensure the arrows align.
[Diagram illustrating the removal and cleaning of the coarse filter, microfilter, and the overall filter system.]
Cleaning the Spray Arms
- Unscrew the upper spray arm and detach it by pulling downwards [arrow pointing down symbol].
- Pull the lower spray arm upwards.
- Check the spray nozzles under running water for blockages and remove any foreign objects.
- Insert the lower spray arm. The spray arm locks with an audible click.
- Insert the upper spray arm and screw it on tightly.
[Diagram showing the removal of the upper and lower spray arms for cleaning.]
Cleaning the Drain Pump
- Disconnect the appliance from the power supply.
- Remove the filter system.
- Drain any remaining water.
- Using a spoon, lift the pump cover by gripping the rib.
- Lift the pump cover diagonally inwards and remove it.
- Remove food residue and foreign objects from the impeller area.
- Insert the pump cover and press it down [arrow pointing down symbol]. The pump cover locks with an audible click.
- Reassemble the filter system.
[Diagram illustrating the process of cleaning the drain pump, including removing the filter, accessing the pump cover, and cleaning the impeller area.]
Troubleshooting
| Fault | Cause and Troubleshooting |
|---|---|
| E:32-00 lights up alternately or water supply indicator is lit. | Inlet hose is kinked. [Check mark] Lay the inlet hose without kinks. Water tap is closed. [Check mark] Open the water tap. Water tap is blocked or calcified. [Check mark] Open the water tap. With the water supply open, the flow rate must be at least 10 l/min. Water connection filters in the supply hose or AquaStop are blocked. 1. Switch off the appliance. 2. Unplug the appliance. 3. Close the water tap. 4. Unscrew the water connection. 5. Remove the filter from the supply hose. 6. Clean the filter. 7. Insert the filter into the supply hose. 8. Connect the water connection. 9. Check the water connection for leaks. 10. Restore power. 11. Switch on the appliance. |
| E:61-02 lights up alternately. | The drain pump is blocked. [Check mark] Clean the drain pump. The drain pump cover is loose. [Check mark] Securely fasten the drain pump cover. |
| E:92-40 lights up alternately. | Filters are dirty or blocked. [Check mark] Clean the filters. |
| Food residue on dishes. | Dishes are packed too tightly or the basket is too full. 1. Load dishes leaving sufficient space between them. Water jets must reach the surface of the dishes. 2. Avoid contact points. The rotation of the spray arms is blocked. Load dishes so that the rotation of the spray arms is not obstructed. Spray nozzles of the spray arms are blocked. [Check mark] Clean the spray arms. Filters are dirty. [Check mark] Clean the filters. Filters are inserted incorrectly and/or not locked. 1. Insert filters correctly. 2. Lock filters. A wash program that is too weak was selected. [Check mark] Select a more powerful wash program. |
| Removable streaks on glasses, metallic-looking glasses, and cutlery. | Rinse aid dosage is set too high. [Check mark] Set the rinse aid system to a lower level. No rinse aid has been added. [Check mark] Add rinse aid. |
| Rust marks on cutlery. | The cutlery is not sufficiently resistant to oxidation. Knife blades are often affected more. [Check mark] Use stainless steel cutlery. Cutlery also oxidizes when washed together with items that oxidize. [Check mark] Do not wash oxidising parts. |
| Detergent residue in the detergent compartment or tablet drawer. | Spray arms were blocked by dishes and the detergent was not rinsed out. [Check mark] Ensure that the spray arms are not blocked and can rotate freely. |
| All LEDs are lit or flashing, or the wash program does not continue. | The electronic system has detected an error. [Check mark] Press the main switch button for approx. 4 seconds. The appliance is reset and restarts. |
