INSTRUCTION

NOTICE

Please keep these instructions for future reference.

Dear Customer

Thank you for your purchase. When you receive the product, please make sure that all the parts are intact. Then follow the entire installation instructions to install!

There is an installation video on the product page; you can open the product page to view it or contact customer service to receive it.

• A. The outer box is damaged.
• B. The product is damaged / bent / cracked while you open the box.
• C. The parts / accessories / assembly tools are missing.
• D. The instructions are not clear and cannot be referred to.
• E. The product has functional problems.
• F. Other aspects that you are not satisfied with.

Please feel free to contact us for help, and provide the following information: Platform/Shop name, Order ID, Buyer's name, Receiver's address, Problem description.

PART LIST (Base 1)

Diagram Description: Components for one coffee table base are shown, including legs (D), slatted panels (G), buckles (N), screws (1, 2), gaskets (3), and an Allen wrench (6). Also depicted are a cushion (F) and a tabletop (E) as part of the assembled furniture set.

ASSEMBLY STEPS (Base 1)

STEP 1

Place the screw (1) through the hole and hold it in place with Tool 6 (Allen Wrench). Rotate the bottom of Part D (Leg) against the screw to hold the screw in place at 90%.

Diagram Description: Shows attaching a leg (D) to a slatted panel (G) using screw (1) and gasket (3), secured by Allen wrench (6). An inset shows rotating part D to secure the screw at 90%.

STEP 2

After tightening the screws, tighten the bottom screws.

Diagram Description: Shows tightening the screws previously installed in Step 1.

STEP 3

Align holes by placing part C (structural component) under part G (slatted panel) to make installation easier. Tighten the screws (2) 40% to proceed to the next step in the installation.

Diagram Description: Shows aligning part C under part G and attaching with screws (2) and gaskets (3). An inset shows the alignment and screw attachment.

STEP 4

Tighten screws 40% and all screws when finished.

Diagram Description: Shows tightening screws previously installed in Step 3.

Completing the Installation.

Diagram Description: Shows a completed coffee table base, resembling one half of the set shown on the first page.

PART LIST (Base 2)

Diagram Description: Components for the second coffee table base are shown, including legs (D), slatted panels (H), buckles (N), screws (1, 2), gaskets (3), and an Allen wrench (4). This base appears similar to Base 1 but may use different slatted panels (H instead of G).

ASSEMBLY STEPS (Base 2)

STEP 5

Place the screw (1) through the hole and hold it in place with Tool 6 (Allen Wrench). Rotate the bottom of Part D (Leg) against the screw to hold the screw in place at 90%.

Diagram Description: Shows attaching a leg (D) to part H (slatted panel) using screw (1) and gasket (3), secured by Allen wrench (4). An inset shows rotating part D to secure the screw at 90%.

STEP 6

After tightening the screws, tighten the bottom screws.

Diagram Description: Shows tightening the screws previously installed in Step 5.

STEP 7

Align holes by placing part C (structural component) under part H (slatted panel) to make installation easier. Tighten the screws (2) 40% to proceed to the next step in the installation.

Diagram Description: Shows aligning part C under part H and attaching with screws (2) and gaskets (3). An inset shows the alignment and screw attachment.

STEP 8

Tighten screws 40% and all screws when finished.

Diagram Description: Shows tightening screws previously installed in Step 7.

Completing the Installation.

Diagram Description: Shows a completed second coffee table base.

TIPS

1. In order to increase the toughness of the sofa fixed buckle (N), please soak it in hot water for 10 minutes before use.
2. When in use, first snap one side of the buckle into the metal frame, and then force the other side into all the frame.
3. You can freely make a variety of combinations using the above methods.

Diagram Description: Shows a buckle (N) being soaked in hot water.

PART LIST (Tabletop)

Diagram Description: Components for the coffee table top assembly are shown, including the slatted surface (K), side panels (J, I), legs (D), gaskets (3), screws (4, 5), and an Allen wrench (6).

ASSEMBLY STEPS (Tabletop)

STEP 9

Tighten the screws (5) 40% to proceed to the next step in the installation.

Diagram Description: Shows attaching a side panel (J) to the slatted tabletop surface (K) using screw (5) and gasket (3), secured by Allen wrench (6). An inset shows the screw attachment.

STEP 10

Tighten the screws (5) 40% to proceed to the next step in the installation.

Diagram Description: Shows attaching a side panel (J) to the slatted tabletop surface (K) using screw (5) and gasket (3), secured by Allen wrench (6).

STEP 11

Tighten screws (5) 40% and all screws when finished.

Diagram Description: Shows attaching a side panel (J) to the slatted tabletop surface (K) using screw (5) and gasket (3), secured by Allen wrench (6). An inset shows the screw attachment.

STEP 12

Place the screw (4) through the hole and hold it in place with Tool 6 (Allen Wrench). Rotate the bottom of Part D (Leg) against the screw to hold the screw in place at 90%.

Diagram Description: Shows attaching a leg (D) to the assembled tabletop structure (likely side panels J/I and K) using screw (4) and gasket (3), secured by Allen wrench (6). An inset shows rotating part D to secure the screw at 90%.

STEP 13

After tightening the screws, tighten the bottom screws.

Diagram Description: Shows tightening the screws previously installed in Step 12.

Completing the Installation.

Diagram Description: Shows a completed coffee table.

AFTER-SALE SERVICE

If you have any suggestions for our products or find that the products have quality problems, please contact us first. Our after-sales team will reply within 24 hours, and we will do our best to give you solutions until you are satisfied.

Guaranteed Customer Service

Your shopping experience is very important to us! Feel unsatisfied? Please contact customer service! Have any questions? Please contact customer service!

Wanna Share how wonderful our smart products make your home? Share your pictures with us. Any suggestions? Please contact customer service! We gotcha back!