HOMCOM 837-394 Shoe Storage Cabinet Assembly Instructions

Important Information & Guidelines

General Guidelines

• Please read these instructions carefully before assembly and use.
• Keep this manual for future reference and pass it on if the product is transferred.
• This product is intended for indoor use only.
• Assemble and use the product strictly according to these instructions.
• Keep the product away from fire sources and high temperatures.
• Assemble on a spacious, clean surface. Avoid placing unpacked items directly on the floor to prevent damage.
• Wear gloves ? during assembly/disassembly to avoid scratches from sharp edges.
• Match parts and fittings using the part numbers provided in the manual.
• Periodically check screw tightness and retighten if necessary to ensure structural integrity.
• Wipe up any spilled water or liquid immediately with a dry towel.
• Place the item on a level, solid surface during use.

Warnings

• Not suitable for children under 3 years of age. Adult supervision is required.
• Do not allow children to climb or play on the product to prevent tipping and serious injury.
• Keep small parts (screws, etc.) out of reach of children during assembly, as they can be a choking or inhalation hazard (potentially fatal).
• Keep all packaging materials (films, plastic bags, foam, etc.) away from babies and children to prevent suffocation hazards.

Parts List

Components

• Part 1: Side Panel (x1)
• Part 2: Side Panel (x1)
• Part 3: Divider Panel (x1)
• Part 4: Front Panel (x1)
• Part 5: Back Panel (x1)
• Part 6: Support Rail (x3)
• Part 7: Drawer Back Panel (x4)
• Part 8: Drawer Side Panel (x4)
• Part 9: Drawer Front Panel (x4)
• Part 10: Drawer Base Panel (x4)

Hardware

• A: Screw (M4*12) (x8, +1 spare)
• B: Screw (M8*40) (x10, +1 spare)
• C: Screw (M6*30) (x8, +1 spare)
• D: Screw (M6*30) (x10, +1 spare)
• E: Panel Connector (x8)
• F-1: Cam Lock Housing (x8)
• F-2: Cam Lock Screw (x8)
• F-3: Washer (x8)
• G-1: Drawer Runner (x5)
• G-2: Drawer Runner (x5)
• H-1: Handle (x2)
• H-2: Back Panel Support (x2)
• I: Drawer Slide Mechanism (x8)
• J: Screw (M3.5*12) (x73, +1 spare)
• K: Screw (M3.5*35) (x3)
• Spare Plastic Hardware (x4)

Assembly Steps

Step 1: Prepare Panels

Attach hardware A1 (likely cam lock screws or dowels) to the designated panels. If using plastic hardware, a hammer ? may be used gently.

Diagram shows attaching a screw/dowel into a pre-drilled hole on a panel. A checkmark ✔️ indicates correct assembly, a cross ❌ indicates incorrect.

Step 2: Assemble Base Structure

Connect the base panels (1, 2) and divider panel (3) using support rails (6). Secure them with screws K (M3.5*35).

Diagram shows panels 1, 2, 3 being joined by rails 6, with screws K being inserted.

Step 3: Attach Side Panels

Connect the side panels (1, 2) to the assembled base structure. Use hardware B (M8*40) and D (M6*30) for secure attachment.

Diagram shows side panels being attached to the base with screws.

Step 4: Attach Front, Back, and Divider Panels

Attach the front panel (4), back panel (5), and internal divider (3) to the structure. Use hardware A (M4*12), B (M8*40), C (M6*30), and D (M6*30) as indicated.

Diagram shows the main cabinet frame being completed with front, back, and internal panels.

Step 5: Install Drawer Runners (Type G-2)

Attach the drawer runners (G-2) to the inside of the cabinet. Secure them using screws J (M3.5*12). Also, install cam lock housings (F-1) and cam lock screws (F-2) into the drawer components.

Diagram shows runners being screwed into the cabinet interior and cam lock components being fitted.

Step 6: Install Drawer Runners (Type G-1)

Attach the remaining drawer runners (G-1) to the inside of the cabinet.

Diagram shows the other set of runners being attached.

Step 7: Assemble Drawer Sides

Connect the drawer side panels (E) to the drawer base panels (10). Use screws J (M3.5*12) for attachment. Ensure the cam lock screws (F-2) are correctly oriented.

Diagram shows drawer sides being attached to the drawer base, with cam lock components visible.

Step 8: Attach Drawer Back and Front Panels

Attach the drawer back panels (7) and drawer front panels (9) to the assembled drawer sides (E) and base (10). Use screws J (M3.5*12).

Diagram shows the back and front panels being attached to the drawer structure.

Step 9: Install Drawer Slide Mechanisms

Attach the drawer slide mechanisms (I) to the assembled drawers and the main cabinet structure. Use hardware F-3 (washers) and I (screws M4*12) for the cabinet, and screws J (M3.5*12) for the drawers.

Diagram shows the drawer slide mechanisms being fitted to both the drawer boxes and the cabinet interior.

Step 10: Insert Drawers into Cabinet

Carefully slide the assembled drawers into the cabinet, aligning them with the installed runners.

Diagram shows drawers being inserted into the cabinet.

Step 11: Attach Handles

Attach the handles (H-1) to the front of each drawer using screws J (M3.5*12).

Diagram shows handles being screwed onto the drawer fronts.

Step 12: Attach Back Panel Supports

Secure the back panel supports (H-2) to the cabinet.

Diagram shows small supports being attached to the back of the cabinet.

Step 13: Final Check

Ensure all drawers open and close smoothly and that the cabinet is stable.

Diagram shows the completed shoe cabinet.