CZEview G6 Battery Camera with Dual Lens

User Manual

Important Safety Instructions

The battery-powered camera is not designed for continuous 24-hour operation or constant live streaming. It is intended for motion event recording and live streaming only when necessary.
Ensure all warnings and instructions on the product are followed.
The product is an aid and should not replace responsible and adequate adult supervision.
Use only manufacturer-approved accessories and attachments.
Please turn off the device when not in use for an extended period.
Charge the battery camera with the specified power adapter. Do not use solar panels from other brands to charge the battery.
Do not attempt to disassemble the product. Contact authorized service centers for maintenance.
Supervise children to prevent them from tampering with the product.
Keep small, detachable parts out of reach of small children to prevent choking hazards.
Do not use by persons with reduced physical, sensory, or mental capabilities without adequate supervision.
Ensure the solar panel receives sufficient sunlight and avoid obstructions (like trees, buildings, or other objects) that may block light.
The solar panel surface may accumulate dust, dirt, or fallen leaves, which can affect light absorption. Regular cleaning (every few months) is recommended.

Battery Precautions

The battery is built-in; do not attempt to remove it from the camera.
Charge the battery at temperatures between 0°C and 45°C, and use the battery at temperatures between -20°C and 50°C.
Keep the charging port dry, clean, and free of debris. Cover it with the rubber cap when the battery is not charging.
Do not charge, use, or store the battery near ignition sources like open flames or heaters.
Do not use the battery if it emits an odor, generates heat, changes color, deforms, or shows any signs of abnormality. If the battery is in use or charging, stop immediately and contact the brand's seller for after-sales service.
Avoid exposure to extreme temperatures and pressures, which could cause explosions or leaks.
Do not dispose of the battery in fire or attempt to damage it mechanically.
Follow proper guidelines for the disposal of used batteries to minimize environmental damage.

Precautions

Handle batteries with care to avoid risks of burns, fire, and explosions.
Protect the product from extreme temperatures, prolonged sun exposure, and keep it away from heat sources.
Prevent strangulation by keeping cables out of children's reach.
Be aware of potential interference from other electronic devices and position the camera unit accordingly.

What's Included

For G6:

CZEview Camera
Wall Mount
Screw Package
Power Cable
User Manual
Solar Panel
Solar Panel Mount

For G6 PRO:

CZEview Camera
Wall Mount
Screw Package
Power Cable
User Manual
Solar Panel

Product Description

Battery-powered camera

Reset Button: To reset, press and hold the Reset button for 3-6 seconds. If the indicator light is off, press the 'Power' button first to turn it on, then press and hold 'Reset' to reset the device.

SD Card Slot: Supports SD card storage up to 256 GB.

Power Button: To turn on or off, press and hold the Power button for 3-6 seconds.

Indicator Lights:

Charging Indicator Light:
Solid Red: Charging
Solid Blue: Fully Charged

Operation Indicator Light:
Solid Red: Device error detected (Please restart and reconnect to Wi-Fi)
Slow Red Flash: Wi-Fi pairing mode activated, waiting for connection
Fast Red Flash: Searching for Wi-Fi networks
Solid Blue: Camera operating normally
Slow Blue Flash: Connecting to Wi-Fi
Fast Blue Flash: Device is updating
Alternating Red and Blue: Connection time out. Press and hold the power button for 3-6s to turn off and on. Reconnect Wi-Fi.

Specifications

Resolution	2.5K (2MP+2MP)
Number of Lenses	2
Battery Capacity	10000MAH
Wi-Fi Band	2.4G
Two-way Audio	Supported
Siren Alarm	Supported
Spotlight Alarm	Supported
Motion Detection	Supported
Color Night Vision	Supported
Pan/Tilt	Pan 355° Tilt 120°
IP Rating	IP65
Operating Temperature	-20°C - 50°C
Local Storage	Micro SD Card (Up to 256GB)
Power Supply (Not Included)	DC 5V/2A
Solar Panel Power	6W

Preparation

Local Monitoring:

A Micro SD card (up to 256GB, NOT INCLUDED) is required for recording and storage. It is optional if video and image storage is not needed.

Cloud Storage Options:

Choose a cloud storage plan for video clips, offering backup and features. Subscription is available after linking the device in the app.

Charging the Camera:

For first-time use, fully charge the camera with the included charging cable and a 5V adapter (not included). The indicator light will turn solid blue when fully charged.

Note: To maintain weather resistance, always cover the charging port with the rubber cap after charging the camera.

Setting Up the System

Download the App:

Download 'CZEview' from the App Store (iOS) or Google Play (Android), or scan the QR code below.

Register and Log In to Your Account:

Launch the app, register an account with a valid email address during your first use, then log in.

Note:

Allow the app to access your WLAN and mobile data for a successful connection.
Allow the app to access push notifications for detection alerts.

Configuring the Camera in the App:

Before you start, please note:

Fully charge the camera before using it for the first time.
Press and hold the 'Power' button for 3-6 seconds until you hear three quick 'Ding, Ding, Ding' sounds, indicating the camera is powering on.
Ensure the red indicator light flashes slowly, signifying it's ready for Wi-Fi configuration.

Method 1: Bluetooth Connection (Recommended)

Note: Allow the app to access your Bluetooth services and location to ensure a successful connection.

On the Home page, select 'Scan code' in the upper right corner to add a device. Then, tap 'Start scanning' and align the camera with the QR code located on the camera body label.
The camera to be connected will appear. Tap 'Enter configuration' to proceed.

Wi-Fi Setup

Follow the on-screen instructions to complete the following steps.
Select the same Wi-Fi network your phone is connected to and enter the password.
Allow the app to access your location.

If a 'connection error' message appears during Wi-Fi setup, tap 'Add again' in the upper left corner and follow these steps:

If the indicator light is on: Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating the camera is in reset mode. The indicator light will flash red and emit three quick 'Ding, Ding, Ding' sounds, signaling the camera is starting up and ready for Wi-Fi configuration.
If the indicator light is off: Press the 'Power' button to turn on the indicator light and hear three quick 'Ding, Ding, Ding' sounds. Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating reset mode. The light will flash red and emit three quick 'Ding, Ding, Ding' sounds, signaling the camera is starting up and ready for Wi-Fi configuration.
Follow the on-screen instructions to complete the connection.

Installing the Camera

If the above steps do not work, tap 'Other Methods' and refer to the 'Important Tips' section for more guidance, or contact CZEview directly at support@czeview.net.

Perform a network diagnosis.

Bring the camera to the area where you plan to install it and open the app.
Tap the 'Settings' icon in the bottom right of the preview window.
Go to 'Installation Guide' and tap it.
Tap 'Next' until you reach the 'Network Diagnosis' page. For best performance, ensure the Wi-Fi signal strength at the installation location is 'Strong'.

For optimal results, install the camera on the wall at a height of approximately 2.5 meters (8.2 feet) from the ground. Ensure there are no obstructions within 1 meter (3.3 feet) of the camera's horizontal field of view. Avoid placing the camera behind trees or in corners, as this may affect night vision quality.
Fix the wall mount to a drillable surface with screws.

For G6
For G6 PRO

Before sliding the camera into the wall mount, note that the upper lens can only be manually adjusted and allows for a 90° rotation to the left and right.
Slide the camera into the wall mount until it clicks into place.
Install the solar panel.

For G6: Mount the bracket on the wall using the included screw package. Attach the solar panel to the bracket and tighten to ensure stability.
For G6 PRO: Align the solar panel with the mounting slot on the top of the wall mount. Adjust the solar panel's direction to face a zone with good sun exposure. Then tighten the screw to fix it.

Adjust the panel's angle for optimal solar exposure. Orienting it south is recommended for better efficiency.
Installation complete. Connect the cable to the camera.

Solar Panel Mounted Directly to the Wall

Align the mounting plate on the wall and fix it with the provided screws. Ensure the panel is oriented towards the sun before fully tightening the screws.
Installation complete. Connect the cable to the camera.

Tips for Optimal Motion Detection

A. Camera Installation Based on Field of View:

Verify your camera's viewing angle to ensure the monitoring area is well within its field of view.
The ideal viewing distance is 2 to 10 meters for optimal recognition. For best results, avoid placing the camera too far or too high; the recommended height is 2.5 meters.

B. Installation Based on PIR Motion Sensor Detection:

The PIR motion sensor detects motion within a maximum range of 10 meters and a horizontal angle of 120°. Ensure movements are within this range to be detected.
The PIR sensor is more sensitive to lateral movements than to movements directly towards the camera.

Tips to Reduce False Alarms

Avoid installing the camera facing bright lights, such as sunlight or bright lamps.
Do not point the camera directly towards the road; it is recommended to place the camera at least 10 meters away from entrances or roads.
Keep the camera away from outlets like air conditioner vents, humidifiers, and projector vents.
Avoid placing the camera facing mirrors or glass surfaces.
Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers, to avoid interference.

Tips to Improve Detection Accuracy:

Adjust the sensitivity level to high.
Position the camera to capture lateral movements rather than direct movements for better motion detection.
Mount the camera at an optimal height of 2.5 meters. Avoid placing it too low or too high, as this can hinder alarm detection.
Ensure the lens is within the PIR sensor's ideal detection range of 2 to 10 meters.

Night Vision

To adjust night vision settings, launch the app and navigate to 'Settings → Image Settings → Full Color Mode.' You can choose from three night vision modes in the app.

Note: Night vision quality can be affected by nearby obstructions. Ensure there are no obstructions within 1 meter of the camera's horizontal field of view. Avoid placing the camera behind trees or in corners.

Recording and Playback

CZEview battery cameras only record when motion is detected, not continuously. Recordings can be saved to a micro SD card (not included) or the cloud (requires subscription).

Before Recording:

I. For Cloud Storage Users:

Tap the 'Settings' icon in the bottom right of the preview window.
Go to 'Cloud Storage Service' and tap it.
Subscribe to a plan to enable recording; without a subscription, the camera will not record.
Return to 'Settings', find 'Motion Detection', and tap it. Ensure the 'Motion Detection' function is enabled (it is enabled by default).

II. For SD Card Users:

Tap the 'Settings' icon in the bottom right of the preview window.
Go to 'Recording Management' and tap it.
Ensure the 'Video Switch' is enabled (it is enabled by default).
Return to 'Settings', find 'Motion Detection', and tap it. Ensure the 'Motion Detection' function is enabled (it is enabled by default).

Playback: