CZEview C6 Solar Surveillance Camera

Table of Contents

• Important Safety Instructions
• Battery
• Precautions
• What's Included
• Product Description
• Specifications
• Preparation
• System Setup
• Camera Installation
• Night Vision
• Recording and Playback
• Important Tips

Important Safety Instructions

• The battery-powered camera is not designed for 24-hour continuous operation or constant live streaming. It is designed to record motion events and offer live streaming only when needed.
• Ensure to follow all warnings and instructions indicated on the product.
• Use only manufacturer-approved accessories and attachments.
• Please power off the device when it is not in use for a prolonged period.
• Charge the battery camera with the power supply specified on the product. Do not use solar panels from other brands to charge the battery.
• Do not attempt to disassemble the product. Contact authorized service centers for maintenance.
• Supervise children to prevent them from tampering with the product.
• Keep small and detachable parts out of the reach of small children to prevent the risk of suffocation.
• It should not be used by persons with reduced physical, sensory, or mental capabilities without adequate supervision.
• Ensure the solar panel receives sufficient sunlight and avoid obstacles (such as trees, buildings, or other objects) that may block the light.
• The surface of the solar panel may accumulate dust, dirt, or fallen leaves, which can affect light absorption. It is recommended to clean the panel regularly, generally every few months.

Battery

• The battery is built-in. Do not attempt to remove it from the camera.
• Charge the battery at temperatures between 0°C and 45°C, and use the battery at temperatures between -20°C and 50°C.
• Keep the charging port dry, clean, and free of debris. Cover it with the rubber cap when the battery is not charging.
• Do not charge, use, or store the battery near ignition sources, such as open flames or heaters.
• Do not use the battery if it emits an odor, generates heat, changes color, deforms, or shows any signs of abnormality. If the battery is in use or charging, stop immediately and contact the brand's seller for after-sales service.
• Avoid exposure to extreme temperatures and pressures, which could cause explosions or leaks.
• Do not dispose of the battery in fire or attempt to damage it mechanically.
• Follow the proper guidelines for disposing of used batteries to minimize environmental damage.

Precautions

• Handle batteries with care to avoid risks of burns, fires, and explosions.
• Protect the product from extreme temperatures, prolonged sun exposure, and keep it away from heat sources.
• Prevent strangulation by keeping cables out of the reach of children.
• Be aware of potential interference from other electronic devices and position the camera unit accordingly.

What's Included

• Solar Camera
• Power Cable
• Screw Package
• Wall Mount
• Mounting Strap
• User Manual

Function Indicator Light

• Solid Red Light: Device error detected (Please restart and reconnect to Wi-Fi)
• Slow Red Flashing: Wi-Fi pairing mode activated, waiting for connection
• Fast Red Flashing: Searching for Wi-Fi networks
• Solid Blue Light: Camera operating normally
• Slow Blue Flashing: Connecting to Wi-Fi
• Fast Blue Flashing: Device is updating
• Alternating Red and Blue: Connection timed out. Press and hold the power button for 3-6 seconds to turn off and on. Reconnect Wi-Fi.

Product Description

Solar Camera

• Antenna: For wireless connectivity.
• Solar Panel: Powers the camera using solar energy.
• PIR Motion Sensor: Detects motion.
• Charge Indicator Light: Solid Red: Charging; Solid Blue: Fully charged.
• Microphone: For audio input.
• Lens: Captures video.
• Spotlights: Provide illumination.
• Speaker: For two-way audio.
• Function Indicator Light: Displays device status.
• Infrared Sensor: For night vision.
• Power Input: For charging the camera.
• Power Button: Press and hold for 3-6 seconds to turn on/off.
• Reset Button: Press and hold for 3-6 seconds to reset the device.
• SD Card Slot: Supports SD card storage up to 256GB.

Specifications

Preparation

Local Monitoring

A Micro SD card (up to 256GB, not included) is required for recording and storage. It is optional if video and image storage is not needed.

Cloud Storage Options

Choose a cloud storage plan for video clips, which offers additional backup and features. Subscription is available after linking the device in the app.

System Setup

Charging the Camera

For first-time use, fully charge the camera using the charging cable. When the indicator light turns solid blue, it means the camera is fully charged.

Note: To maintain weather resistance, always cover the charging port with the rubber cap after charging the camera.

Download the Application

Download 'CZEview' from the App Store (iOS) or Google Play (Android), or scan the QR code below.

[QR Code for App Download]

Method 1: Connection via Bluetooth (Recommended)

Note: Allow the app to access your Bluetooth services and location to ensure a successful connection.

1. On the Home page, select 'Scan Code' in the upper right corner to add a device. Then, tap 'Start Scanning' and align the camera with the QR code located on the camera body label.
2. The camera to be connected will appear. Tap 'Enter Configuration' to proceed.
3. Follow the on-screen instructions to complete the following steps.
4. Select the same Wi-Fi network your phone is connected to and enter the password.
5. Allow the application to access your location.

Register and Log In to Your Account

Launch the application, register an account with a valid email address during your first use, then log in.

Note:

1. Allow the application to access your WLAN and mobile data for a successful connection.
2. Allow the application to access push notifications for detection alerts.

Important Notes for Wi-Fi Setup:

• Ensure your network is stable and keep the camera and phone close to the router during setup.
• Enter the Wi-Fi password (8-32 characters) exactly as shown.
• Do not use emojis, special characters, or symbols in your Wi-Fi name or password. Avoid public networks.
• Networks with web authentication are not compatible.
• Ensure your Wi-Fi network name (SSID) is visible.
• VPNs and proxy servers are not compatible.

Configure the Camera in the Application

Before you start, please note:

1. Fully charge the camera before using it for the first time.
2. Press and hold the 'Power' button for 3-6 seconds until you hear three rapid 'Ding, Ding, Ding' sounds, indicating the camera is powering on.
3. Verify that the red indicator light is flashing slowly, which means it is ready for Wi-Fi configuration.
4. If the red light is not flashing, press the 'Power' button to activate the camera, then press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound. Then, you will hear three rapid 'Ding, Ding, Ding' sounds, and the red light will flash slowly, indicating it is ready for Wi-Fi configuration.
5. Ensure the CZEview application is downloaded and open.
6. Select the correct device type and model in the application.

Troubleshooting Wi-Fi Connection:

• If the indicator light is on: Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating the camera is in reset mode. The indicator light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, signaling that the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.
• If the indicator light is off: Press the 'Power' button to turn on the indicator light and listen for three rapid 'Ding, Ding, Ding' sounds. Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating reset mode. The light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, signaling that the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.

Precautions:

1. If a 'connection error' message appears during Wi-Fi configuration, tap 'Add Again' in the upper left corner and follow these steps:
• If the indicator light is on: Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating the camera is in reset mode. The indicator light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, signaling that the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.
• If the indicator light is off: Press the 'Power' button to turn on the indicator light and listen for three rapid 'Ding, Ding, Ding' sounds. Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound, indicating reset mode. The light will flash red and emit three rapid 'Ding, Ding, Ding' sounds, signaling that the camera is starting up and ready for Wi-Fi configuration. Follow the on-screen instructions to complete the connection.
2. If the above steps do not work, tap 'Other Methods' and refer to the 'Important Tips' section for further guidance, or contact us directly at support@czeview.net.

Camera Installation

Network Diagnosis

1. Perform a network diagnosis.
2. Bring the camera to the area where you plan to install it and open the app. Tap the 'Settings' icon in the bottom right of the preview window. Navigate to 'Installation Guide' and tap it. Tap 'Next' until you reach the 'Network Diagnosis' page. For optimal performance, ensure the Wi-Fi signal strength in the installation location is 'Strong'.

Choosing Installation Tools

Choose the installation tools that suit your needs.

I. Using the Wall Mount

1. Fix the wall mount to a drillable surface with screws.
2. Slide the camera onto the wall mount until it clicks into place.

II. Using the Strap

1. Pass the strap through the opening in the wall mount.
2. Pass the strap through the buckle, adjust it, and fasten it to a pole or tree.

Installation Tips

• For optimal results, install the camera on the wall at a height of approximately 2.5 meters from the ground. Ensure there are no obstacles within 1 meter of the camera's horizontal field of view. Avoid placing the camera behind trees or in corners, as this may affect night vision quality.

Installation Based on PIR Motion Sensor Detection

• The PIR motion sensor detects motion within a maximum range of 10 meters and a horizontal angle of 130°. Ensure that movements are within this range to be detected.
• The PIR sensor is more sensitive to lateral movements than to movements directly towards the camera.

Tips for Optimal Motion Detection:

A. Camera Installation Based on Field of View:

1. Verify your camera's viewing angle to ensure the monitored area is well within its field of view.
2. The ideal viewing distance is 2 to 10 meters for optimal recognition. For best results, avoid placing the camera too far or too high; the recommended height is 2.5 meters.

B. Installation Based on PIR Motion Sensor Detection:

• The PIR motion sensor detects motion within a maximum range of 10 meters and a horizontal angle of 130°. Ensure that movements are within this range to be detected.
• The PIR sensor is more sensitive to lateral movements than to movements directly towards the camera.

Tips for Reducing False Alarms:

• Avoid installing the camera facing bright lights, such as sunlight or bright lamps.
• Do not point the camera lens directly at the road; it is recommended to place the camera at least 10 meters away from driveways or roads.
• Keep the camera away from vents such as air conditioner vents, humidifiers, and projector vents.
• Avoid placing the camera facing mirrors or glass surfaces.
• Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers, to avoid interference.

Tips for Improving Detection Accuracy:

• Adjust the sensitivity level to high.
• Position the camera to capture lateral movements rather than direct movements for better motion detection.
• Mount the camera at an optimal height of 2.5 meters. Avoid placing it too low or too high, as this may make alarm detection difficult.
• Ensure the lens is within the ideal detection range of the PIR sensor, from 2 to 10 meters.

Night Vision

To adjust night vision settings, launch the app and navigate to 'Settings → Image Settings → Full Color Mode.' You can choose from three night vision modes in the app.

Note: The quality of night vision may be affected by nearby obstacles. Ensure there are no obstacles within 1 meter of the camera's horizontal field of view. Avoid placing the camera behind trees or in corners.

Recording and Playback

CZEview battery cameras only record when motion is detected, not continuously. Recordings can be saved to a micro SD card (not included) or to the cloud (subscription required).

Before Recording:

I. For SD Card Users:

• Use a micro SD card with a capacity between 8GB and 256GB. (A 32GB SD card can store up to 6 months of video for reference.)
• After inserting the SD card, go to 'Settings' → 'Recording Management' to check if 'SD Card Capacity' appears in the app. If it does, tap 'Format' to prepare the card.
• If 'SD Card Capacity' does not appear, reinsert the SD card and check again in 'Recording Management'. If the problem persists, try another SD card.

II. For Cloud Storage Users:

The camera includes basic free cloud storage for life, where motion-activated videos are saved for 7 days before being overwritten. The free cloud storage plan records 6-second clips. For longer recordings, consider subscribing to another cloud storage plan or using an SD card.

Configuring Recording:

I. For Cloud Storage Users:

• Tap the 'Settings' icon in the bottom right of the preview window.
• Go to 'Cloud Storage Service' and tap it.
• Subscribe to a plan to enable recording; without a subscription, the camera will not record.
• Return to 'Settings', find 'Motion Detection', and tap it.
• Ensure the 'Motion Detection' function is enabled (it is enabled by default).

II. For SD Card Users:

• Tap the 'Settings' icon in the bottom right of the preview window.
• Go to 'Recording Management' and tap it.
• Ensure the 'Video Switch' is enabled (it is enabled by default).
• Return to 'Settings', find 'Motion Detection', and tap it.
• Ensure the 'Motion Detection' function is enabled (it is enabled by default).

Playback:

I. For Cloud Storage Users:

• On the home page, tap the playback icon ▶️.
• Tap 'Cloud' to view videos stored in the cloud.
• For a paid cloud storage plan, the default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'. The basic cloud storage plan only supports 6-second recordings.

II. For SD Card Users:

• On the home page, tap the playback icon ▶️.
• Tap 'History' to view videos stored on the SD card.
• The default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'.

Important Tips

For detailed instructions on 'CAMERA CONFIGURATION IN THE APPLICATION', 'APPLICATION FUNCTIONS', and 'TROUBLESHOOTING', scan the QR code below.

[QR Code for Detailed Instructions]