CZEview Solar-Powered Surveillance Camera User Manual

Important Safety Information

• The battery-powered camera is not designed for 24/7 operation or continuous live streaming. It is designed to record motion events and offer live streaming only when needed.
• Follow all warnings and instructions marked on the product.
• Use only attachments and accessories recommended by the manufacturer.
• Turn off the device when it is not in use for an extended period.
• Charge the battery-powered camera using the power source indicated on the product. Do not use solar panels from other brands to charge the battery.
• Do not attempt to disassemble the device. Contact authorized service facilities for servicing.
• Supervise children to prevent them from playing with the product.
• Keep small, detachable parts out of the reach of small children to avoid choking hazards.
• Not intended for use by persons with reduced physical, sensory, or mental capabilities without adequate supervision.
• Ensure the solar panel receives sufficient sunlight and avoid obstructions (like trees, buildings, or other objects) that might block the light.
• The surface of the solar panel may accumulate dust, dirt, or leaves, which can affect light absorption. It is recommended to clean the panel regularly, typically every few months.

Battery Information

• The battery is built-in. Do not attempt to remove it from the camera.
• Charge the battery at temperatures between 0°C and 45°C, and use the battery at temperatures between -20°C and 50°C.
• Keep the charging port dry, clean, and free from dirt. Cover it with the rubber cap when the battery is not charging.
• Do not charge, use, or store the battery near ignition sources such as open flames or heaters.
• Do not use the battery if it emits an odor, heats up, discolors, deforms, or appears abnormal in any way. If the battery is used or charged, stop the process immediately and contact the brand's seller for customer service.
• Avoid exposure to extreme temperatures and pressures, which can cause explosions or leaks.
• Do not dispose of the battery in fire or attempt to damage it mechanically.
• Follow proper disposal guidelines for used batteries to minimize environmental damage.

What's Included

• Solar-Powered Camera
• Power Cable
• Screw Set
• Wall Mount
• Mounting Strap
• User Manual

Product Overview

The CZEview Solar-Powered Camera features:

• SD Card Slot: Supports up to 256GB.
• Power Button: Press and hold for 3-6 seconds to turn the device on or off.
• Antenna
• Solar Panel
• PIR Motion Sensor
• Charging Indicator Light: Solid red light indicates charging; solid blue light indicates fully charged.
• Microphone
• Spotlight
• Working Indicator Light
• Infrared Sensor
• Lens
• Speaker
• Reset Button: Press and hold for 3-6 seconds to reset. If the indicator light is off, press the 'Power' button first to turn on the light, then hold 'Reset' to reset the device.
• Power Input

Precautions

• Handle batteries with care to avoid burns, fire, and explosion hazards.
• Protect the product from extreme temperatures, direct sunlight, and keep it away from heat sources.
• Prevent strangulation by keeping cables out of the reach of children.
• Be aware of potential interference from other electronic devices and position the camera unit accordingly.

Specifications

Preparation

Local Monitoring

A Micro-SD card (up to 256GB, not included) is required for recording and storage. It is optional if no video or image storage is needed.

Cloud Storage Options

Choose a cloud storage plan for video clips, which provides additional backup and features. Subscription is available after connecting the device in the app.

Charging the Camera

For first-time use, please fully charge the camera using the charging cable. When the indicator light shows a solid blue light, it means the camera is fully charged.

System Setup

Download the App

Download 'CZEview' from the App Store (iOS) or Google Play (Android), or scan the QR code below.

[App Store QR Code]

[Google Play QR Code]

Register and Log In to Your Account

Launch the app, register using a valid email address on your first use, and log in.

Setting Up the Camera in the App

Before starting:

1. Fully charge the camera before the first use.
2. Press and hold the 'Power' button for 3-6 seconds until you hear three quick 'Ding, Ding, Ding' tones, indicating the camera is starting.
3. Check if the red indicator light is blinking slowly, meaning the camera is ready for Wi-Fi setup.
4. If the red light is not blinking, press the 'Power' button to activate the camera, then press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' sound. Then, you will hear three quick 'Ding, Ding, Ding' tones, and the red light will blink slowly, indicating the camera is ready for Wi-Fi setup.
5. Ensure the 'CZEview' app is downloaded and opened.
6. Select the correct device type and model in the app.
7. Ensure your network is stable and keep the camera and phone close to the router during setup.
8. Enter the Wi-Fi password (8-32 characters) exactly as it appears in the manual.
9. Do not use emojis, special characters, or symbols in your Wi-Fi name or password. Avoid public networks.
10. Networks with web authentication are not supported.
11. Ensure your Wi-Fi network name (SSID) is visible.
12. VPNs and proxy servers will not work.

Method 1: Connecting via Bluetooth (Recommended)

Note: Please allow the app to access your Bluetooth and location services for a successful connection.

1. On the home screen, select 'Scan Code' in the top right to add a device. Then tap 'Start Scan' and point the camera at the QR code on the camera body sticker.
2. The camera to be connected will be displayed. Tap 'Start Configuration' to proceed.
3. Follow the on-screen instructions to complete the next steps.
4. Select the same Wi-Fi network your phone is connected to and enter the password.
5. Allow the app to access your location.
6. Wait for the 'cuckoo' sound, which signals the start of the connection. The indicator light should turn solid blue, confirming successful setup. Then, let the app establish a connection to the camera on your local network and press 'Next' to name your camera.

Caution:

1. If a 'Connection Error' message appears during Wi-Fi setup, tap 'Add Again' in the top left corner and follow these steps:

• If the indicator light is on: Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' tone, indicating the reset mode. The indicator light will blink red, and three quick 'Ding, Ding, Ding' tones will sound, signaling the camera is booting up and ready for Wi-Fi setup. Follow the on-screen instructions to complete the connection.
• If the indicator light is off: Press the 'Power' button to turn on the indicator light and listen for three quick 'Ding, Ding, Ding' tones. Press and hold the 'Reset' button for 3-6 seconds until you hear a 'cuckoo' tone, indicating the reset mode. The light will blink red and emit three quick 'Ding, Ding, Ding' tones, indicating the camera is starting and ready for Wi-Fi setup. Follow the on-screen instructions to complete the connection.

Camera Installation

1. Perform a network diagnosis. Bring the camera to the planned installation location and open the app.
• Tap the 'Settings' icon in the bottom right of the preview screen.
• Navigate to 'Installation Guide' and tap it.
• Tap 'Next' until you reach the 'Network Diagnosis' page. For optimal use, ensure the Wi-Fi signal strength at the installation location remains 'Strong'.
2. For optimal results, install the camera at a height of approximately 2.5 meters above the ground on a wall. Ensure there are no obstructions within 1 meter in the camera's horizontal field of view. Avoid placing the camera behind trees.
3. Choose the installation tools that suit your needs.
• Using the Wall Mount:
• ① Secure the wall mount to a drillable surface using screws.
• ② Slide the camera into the wall mount until it clicks securely.
• Using the Strap:
• ① Thread the strap through the opening in the wall mount.
• ② Thread the strap through the buckle, tighten it, and secure it to a post or tree.

Tips for Optimal Motion Detection:

A. Camera Installation Based on Field of View:

1. Check your camera's viewing angle to ensure the surveillance area is well within the field of view.
2. The ideal viewing distance is 2-10 meters for optimal detection. For best results, the camera should not be installed too far or too high; the recommended height is 2.5 meters.

B. Installation Based on PIR Motion Sensor Detection:

1. The PIR motion sensor detects motion within a maximum range of 10 meters and a horizontal angle of 130°. Ensure that motion within this range is captured.
2. The PIR sensor is more sensitive to side-to-side movements than direct movements towards the camera.

Tips for Reducing False Alarms:

1. Avoid installing the camera facing bright lights such as sunlight or bright lamps.
2. Do not point the camera lens directly at the street; it is recommended to place the camera at least 10 meters away from driveways or roads.
3. Keep the camera away from vents such as air conditioner outlets, humidifiers, and heat vents from projectors.
4. Avoid pointing the camera at mirrors or glass surfaces.
5. Keep the camera at least 1 meter away from any wireless devices, including Wi-Fi routers, to avoid interference.

Improving Detection Accuracy:

1. Set the sensitivity level to high.
2. Position the camera to detect side-to-side movements rather than direct approach for better motion detection.
3. Mount the camera at an optimal height of 2.5 meters. Avoid installing it too low or too high, as this may affect alarm detection.
4. Ensure the target is within the ideal detection range of the PIR sensor, from 2 to 10 meters.

Night Vision

To adjust night vision settings, start the app and navigate to 'Settings → Image Settings → Full Color Mode.' You can choose from three night vision modes in the app.

Note: Night vision quality may be affected by nearby obstructions. Ensure there are no obstructions within 1 meter in the camera's horizontal field of view. Avoid placing the camera behind trees or around corners.

Recording and Playback

CZEview battery-powered cameras only record when motion is detected, not continuously. Recordings can be stored on a microSD card (not included) or in the cloud (subscription required).

Before Recording:

I. For SD Card Users:

• Use a microSD card with a capacity between 8GB and 256GB. (A 32GB SD card can store up to 6 months of video, for reference.)
• After inserting the SD card, go to 'Settings' → 'Recording Control' to check if 'SD Card Capacity' is displayed in the app. If so, tap 'Format' to prepare the card.
• If 'SD Card Capacity' is not displayed, reinsert the SD card and check under 'Recording Control'. If the problem persists, try a different SD card.

II. For Cloud Storage Users:

• The camera includes a lifetime, free 7-day basic cloud storage where motion-triggered videos are stored for 7 days before being overwritten.
• The free basic cloud plan records 6-second clips. For longer recordings, subscribe to a different cloud plan or use an SD card.

Setting Up Recording:

I. For Cloud Storage Users:

• Tap the 'Settings' icon in the bottom right of the preview screen.
• Go to 'Cloud Storage Service' and tap it.
• Subscribe to a plan to enable recording; without a subscription, the camera will not record.
• Go back to 'Settings', find 'Motion Detection', and tap it.
• Ensure the 'Motion Detection' function is enabled (it is enabled by default).

II. For SD Card Users:

• Tap the 'Settings' icon in the bottom right of the preview screen.
• Go to 'Recording Control' and tap it.
• Ensure the 'Video Switch' is enabled (it is enabled by default).

Playback:

I. For Cloud Storage Users:

• On the home screen, tap the playback icon.
• Tap 'Cloud' to view videos stored in the cloud.
• For paid cloud storage plans, the default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'. The basic cloud storage plan only supports 6-second recordings.

II. For SD Card Users:

• On the home screen, tap the playback icon.
• Tap 'History' to view videos stored on the SD card.
• The default recording time is 10 seconds. To extend it, go to 'Settings' → 'Motion Detection'.

Important Tips

For detailed instructions on 'Setting Up the Camera in the App', 'App Functions', and 'Troubleshooting', please scan the QR code below.

[QR Code for detailed instructions]