Assembly Instructions

TABLE

CAUTION: This table is NOT a TOY. Keep your child / children at bay during the assembly process.

Parts List

Hardware

Assembly Preparation

Before Beginning Assembly:

• Read instructions, cover to cover.
• Have 2 adults on hand for assembly.
• Do not assemble on flooring or carpet.
• Assemble on a clean non-marring surface (packing foam).
• Save all packaging until finished.

[Illustration showing the table top, four legs, and central ring laid out on a clean surface.]

Assembly Steps

Overview

[Diagram showing the assembled table structure with labels: Table Top (A) at the top, four Table Legs (B) with pre-attached levellers attached to the underside, and a Central Round Support Ring (C) connecting the legs. An arrow indicates 'FRONT FACING'.]

This table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.

Step 1

[Illustration of all table parts laid out on a clean, soft surface: the table top, four legs, and the central ring.]

Unpack and place all parts on a clean soft surface.

Step 2

[Close-up illustration showing the assembly of one Table Leg (B) to the Central Round Support Ring (C). The sequence is: Washer (①), Spring Washer (②), Hex Bolt (③) passing through the ring and leg, secured by the Spanner (④).]

Loosely attach the Central Round Support Ring (C) to Table Leg (B) using Washers (①), Spring Washers (②), and Hex Bolts (③) with the Spanner (④). Do not fully tighten Bolts.

Step 3

[Illustration showing three Table Legs (B) already attached to the Central Round Support Ring (C), with space for the fourth leg. The connection detail is similar to Step 2.]

Repeat Step 2, attaching the remaining 3 Legs to the Central Round Support Ring (C). Do not fully tighten Bolts.

Step 4

[Illustration of the table base (legs and support ring) being attached to the underside of the Table Top (A), which is placed face down. A close-up shows the hardware sequence: Washer (①), Spring Washer (②), Hex Bolt (③) connecting the leg to the top, secured by Spanner (④).]

Lay the Table Top (A), top facedown, onto a flat, soft, clean surface. Loosely attach the Table Legs (B) to the Table Top (A) using Washers (①), Spring Washers (②), and Hex Bolts (③) with the Spanner (④). Do not fully tighten Bolts.

Step 5

[Illustration of the table standing upright. Callouts point to the pre-installed levellers on the legs, with text indicating 'Adjust height for balance' and 'Adjust low for balance'.]

Stand the table rightside up. Now, in a sequential manner, proceed to securely tighten up all screws. Adjust the Legs Pre-installed Levellers until the Table is level with the ground. Your table is now ready for use.

Caution: This TABLE can only be used on a flat, level surface.

Care & Maintenance

• [hot-item-warning] Do not put hot items directly on furniture surface.
• [cleaning-warning] Do not clean furniture with harsh cleansers or polish.
• [sun-exposure-recommendation] To obtain the longest lifespan of your outdoor products, minimizing exposure to direct sunlight is recommended.
• [child-safety-warning] Children should not climb or jump on the furniture.
• [writing-warning] Do not write on furniture without a padded barrier to protect the surface.
• [weather-protection-recommendation] To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the product and/or place under patio or awnings.
• [commercial-use-restriction] Not for commercial use. For residential use only.
• [stain-removal-tip] Stains may be removed with mild soap solution and damp cloth.
• [cleaning-tip] Dust and pick-up spills using a clean, non-colored, lint-free cloth.