Assembly Instructions
Caution: You must read this before you proceed.
Please look underneath the table top for hardware packs.
TABLE
A line drawing of an outdoor table with a slatted top and curved legs.
CAUTION: This Table is NOT a TOY.
Keep your child / children at bay during the assembly process. For moving the Table and to prevent damage to the Table, two adults are needed to execute this action.
Parts List
| Label | Description | QTY |
|---|---|---|
| A | Table Top | 1 |
| B | Leg | 4 |
| C | Leg Support | 4 |
Hardware
| Label | Description | QTY |
|---|---|---|
| 1 | Bolt (M6x50mm) | 9 |
| 2 | Screw (M6x35mm) | 9 |
| 3 | Washer | 9 |
| 4 | Allen Wrench | 1 |
Assembly Preparation
Before Beginning Assembly:
- Read instructions thoroughly.
- Have 2 adults available for assembly. ???
- Do not assemble on flooring or carpet. ❌
- Assemble on a clean, non-marring surface, such as packing foam. ✔️
- Save all packaging until assembly is complete. ?
Diagram showing all parts and hardware laid out for assembly: table top, four legs, four leg supports, bolts, screws, washers, and an Allen wrench.
Assembly Steps
Overview
An overview diagram showing the assembled table with labels pointing to the Table Top (A), Legs (B), and Leg Supports (C). The front of the table is indicated.
This table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
A close-up view showing how to attach a Leg (B) to the Table Top (A) using a Bolt (1) and Washer (3), tightened with an Allen Wrench (4). Only loosely tighten the bolts. Repeat the same process with the remaining three Legs (B).
Step 3
Diagrams illustrating the attachment of Leg Supports (C) between the Table Top (A) and Legs (B). Step 3.1 shows securing the support to the Table Top with Screw (2) and Allen Wrench (4). Step 3.2 shows securing the support to the Leg with Screw (2) and Allen Wrench (4). Only loosely tighten the screws. Repeat the same process with the remaining three Leg Supports (C).
Step 4
A line drawing of the fully assembled table.
With assistance from your adult partners, turn the table over. Exert pressure, floorwards onto the table with both hands. This pressure will help the table reach full alignment at all joints. Check for wobbles. In a sequential manner, gradually tighten all bolts and screws at all joints until evenly secured.
CAUTION: When tightening the screws and bolts, tighten sequentially. DO NOT tighten any bolt or screw fully and then move towards the next one. This could cause the frame to warp.
If there are still wobbles, loosen the screws and bolts and execute this same above process. If the table is not stable, it could lead to damage to the product. Inspect table and make sure all parts are adequately connected.
Your table is ready for use. This table can only be used on a flat, level surface.
Care & Maintenance
- Do not place hot items directly on the furniture surface. ❌?
- Avoid cleaning furniture with harsh cleansers or polish. ❌?
- To maximize the lifespan of outdoor products, minimize direct sunlight exposure. ☀️
- Children should not climb or jump on the furniture. ❌?
- Avoid writing on furniture without a protective padded barrier. ❌✍️
- To maximize the lifespan of outdoor products, avoid prolonged exposure to rain, snow, and direct sun. Use covers or place under patios/awnings when possible. ?️❄️☀️➡️☂️
- For residential use only. Not for commercial use. ?
- Remove stains with a mild soap solution and a damp cloth. ??
- Dust and wipe up spills with a clean, lint-free cloth. ?
