Hooke Road Roof Rack Installation Instructions
Model: BXG.1069-S
ATTENTION: Please verify all parts are present and read instructions carefully before starting installation. Please feel free to contact your distributor if you have any questions about your purchase.
Contents
A diagram shows the roof rack components. A table lists the parts, quantities, sizes, and provides visual representations of each part.
| Qty | Part Name | Size(mm) | Picture |
|---|---|---|---|
| 2 | Button Bolts | M8×25 | |
| 34 | Button Bolts | M8×20 | |
| 4 | Hex Head Flange Bolts | M8×20 | |
| 8 | Button Bolts | M6×10 | |
| 38 | Flat Washer | M8×20×1.5 | |
| 8 | Flat Washer | M6×12×1.5 | |
| 8 | Flange Hex Lock Nuts | M8 | |
| 8 | Tee Sliding Slot Nuts | M6 | |
| 2 | EVA | 70×37×2 | |
| 2 | EVA | 68×28×2 | |
| 2 | Long Aluminum Crossbars | ||
| 2 | Mounting Brackets | ||
| 2 | Mounting Brackets Covers | ||
| 2 | Rubber Mat | 79×15×6 | |
| 2 | Nylon Round Spacer | M8×20×7 | |
| 2 | Rivet Nut Plate | M8 |
Visuals of parts include: Roof Faring, Passenger Side Side Rail, Front Faring, Driver Side Side Rail, Long Aluminum Crossbars, Mounting Brackets, Front Mounting Brackets Covers, Short Aluminum Crossbar, Mounting Brackets Covers.
Tools Required
- ⚙️ Drive Ratchet Handle
- ⚙️ 4mm, 5mm Hex Bit Socket
A QR code is provided to view online instructions.
Installation Instruction
-
Step 1: Short Aluminum Crossbar Assembly
Assemble the short aluminum crossbar using (8) M6x10 Button Bolts, (8) M6x12x1.5 Flat Washers, and (8) M6 T-nuts. A diagram illustrates this step.
-
Step 2: Front & Rear Farings Assembly
Assemble the front and rear farings. Repeat this step on the other side of the roof rack. Do not fully tighten to allow adjustability. Use (8) M8x20 Button Bolts, (8) M8x20x1.5 Flat Washers, and (8) M8 Flange Hex Lock Nuts. Diagrams illustrate this step.
-
Step 3: Secure Mounting Brackets
Secure the mounting brackets to the side rails. Do not fully tighten to allow adjustability. Repeat this step on the other side of the roof rack. Use (4) M8x20 Hex Head Flange Bolts, (4) M8x20x1.5 Flat Washers, and (2) M8 Rivet Nut Plates. Diagrams illustrate this step.
-
Step 4: Attach Rubber Mat and EVA
Snap the Rubber Mat into the front mounting brackets. Stick the EVA to the front mounting brackets covers and rear mounting brackets. Use (2) 79*15*6 Rubber Mat, (2) Front Mounting Brackets, (2) Front Mounting Brackets Covers, (2) EVA 70×37×2, (2) EVA 68×28×2, and (2) Rear Mounting Brackets. Images show the placement of these components.
-
Step 5: Long Aluminum Crossbar Assembly
Assemble the long aluminum crossbars. Repeat this step on the other position of the roof rack. Do not fully tighten to allow adjustability. Use (20) M8x20 Button Bolts and (20) M8x20x1.5 Flat Washers. A diagram illustrates this step.
-
Step 6: Secure Rear Mounting Brackets
Secure the rear mounting brackets to the vehicle. Do not fully tighten to allow adjustability. Use (4) Factory Bolts. Images show the attachment points on the vehicle.
-
Step 7: Lift and Adjust Roof Rack
Lift the roof rack to the roof of the vehicle and adjust it to the desired location. Do not fully tighten to allow adjustability. Use (4) M8x20 Button Bolts and (4) M8x20x1.5 Flat Washers. A diagram illustrates this step.
-
Step 8: Install Mounting Bracket Covers
Install the mounting bracket covers. At last, tighten up all bolts. Use (2) M8x25 Button Bolts, (2) M8x20x7 Nylon Round Spacer, (2) M8x20 Button Bolts, and (2) M8x20x1.5 Flat Washers. Diagrams show the tightening sequence: tighten the upper bolt first, and then the lower bolt.
-
Step 9: Installation Complete
The installation is complete. Enjoy your off-road life with this Hooke Road product!
A final image shows the installed roof rack on a vehicle.
Find more Hooke Road parts by searching on Google. Share your vehicle on social media @HookeRoad4x4 with the hashtag #hookeroad.
