(1) Contents:
| Qty | Part Name | Size(mm) |
|---|
| 36 | Button Head Socket Cap Bolts Screws | M8*16 |
| 4 | Button Head Socket Cap Bolts Screws | M8*25 |
| 12 | Button Head Socket Cap Bolts Screws | M6*20 |
| 4 | Button Head Socket Cap Bolts Screws | M6*16 |
| 8 | Button Head Socket Cap Bolts Screws | M6*10 |
| 40 | Flat Washer | M8*20*1 |
| 12 | Flat Washer | M6*16*1 |
| 12 | Flat Washer | M6*12*1 |
| 12 | Flange Hex Lock Nuts | M8 |
| 16 | Flange Hex Lock Nuts | M6 |
| 8 | Tee Sliding Slot Nuts | M6 |
Components pictured: Rear Fairing, Front Side Side Rails (x2), Front Fairing, Rear Side Side Rails (x2), Short Crossbar, Crossbars (x7), Connecting Brackets, Front Roof Mount Brackets, Rear Roof Mount Brackets.
Installation Instructions
Step 1: Assemble Rear Half
Open the package and verify all accessories are present. The roof rack consists of front and rear sections. Begin by assembling the rear half. Connect the rear side rails and the rear fairing using M8*16 screws and nuts.
Diagram Description: Shows the rear half of the roof rack structure with side rails and rear fairing being attached using screws and nuts. [Front Arrow] indicates the front direction.
Parts Used: (4) M8*16 Button Head Socket Cap Bolts Screws, (4) M8*20*1 Flat Washer, (4) M8 Flange Hex Lock Nuts.
Step 2: Install Rear Crossbars
Assemble the three crossbars into the rear section using M8*16 screws and washers.
Diagram Description: Illustrates the rear section of the roof rack with three crossbars being secured with M8*16 screws and washers. [Front Arrow] indicates the front direction.
Parts Used: (12) M8*16 Button Head Socket Cap Bolts Screws, (12) M8*20*1 Flat Washer.
Step 3: Bracket Identification
When installing brackets, differentiate between the outer and inner brackets. The outer bracket is larger than the inner bracket. Identify left and right sides by the shape of the bracket's end: the angled edge is for the driver's side, and the right angle is for the passenger side.
Diagram Description: Shows two sets of brackets labeled "Outside Brackets" and "Inside Brackets". Each set indicates "Driver Side" and "Passenger Side", with visual cues for differentiation.
Step 4: Install Rear Mounting Bracket
After identifying the correct positions, install the rear mounting bracket in the rear section using M8*25 screws, washers, and nuts. Do not overtighten the screws at this stage.
Diagram Description: Depicts the rear section of the roof rack with the rear mounting bracket being attached using M8*25 screws, washers, and nuts. [Front Arrow] indicates the front direction.
Parts Used: (4) M8*25 Button Head Socket Cap Bolts Screws, (4) M8*20*1 Flat Washer, (4) M8 Flange Hex Lock Nuts.
Step 5: Secure Rear Half to Vehicle
Lift the assembled rear half of the roof rack and secure the rear mounting bracket into the vehicle's recess. Tighten the bracket's installation screws once it is fully inserted.
Diagram Description: Shows the assembled rear half of the roof rack being placed into a vehicle's roof recess. Close-up views illustrate the inside and outside mounting points, with red arrows indicating the attachment locations.
Step 6: Assemble Front Fairing and Short Crossbar
Assemble the front part. Install the short crossbar into the front fairing. First, place the Tee Sliding Slot Nuts inside the grooves of the short aluminum bars. Align them with the holes on the front fairing and secure them using M6*10 screws and M6*12*1 flat washers.
Diagram Description: Illustrates the front fairing assembly with the short crossbar, Tee Sliding Slot Nuts, M6*10 screws, and M6*12*1 flat washers.
Step 7: Install Front Mounting Bracket
Install the front mounting bracket onto the front panel using M6*16 screws and M6*12*1 washers and nuts. Do not tighten the screws yet.
Diagram Description: Shows the front panel with the front mounting brackets being attached using M6*16 screws, M6*12*1 washers, and M6 Flange Hex Lock Nuts. [Front Arrow] indicates the front direction.
Parts Used: (4) M6*16 Button Head Socket Cap Bolts Screws, (4) M6*12*1 Flat Washer, (4) M6 Flange Hex Lock Nuts.
Step 8: Mount Front Fairing to Vehicle
Remove the cover above the front glass of the original vehicle. Place the assembled front fairing onto your vehicle and install it using the factory bolts.
Diagram Description: Shows close-up views of the vehicle's roof edge above the front windshield, highlighting the mounting points where the front fairing is attached. Red circles indicate specific attachment areas.
Step 9: Install Front Side Rails
Install the side rails on both sides of the front fairing using M8*16 screws, washers, and nuts for assembly.
Diagram Description: Depicts the front section of the roof rack with side rails being attached to the front fairing using M8*16 screws, washers, and nuts. [Front Arrow] indicates the front direction.
Parts Used: (4) M8*16 Button Head Socket Cap Bolts Screws, (4) M8*20*1 Flat Washer, (4) M8 Flange Hex Lock Nuts.
Step 10: Install Front Crossbars
Install four crossbars into the front half part using M6*16 screws and washers, and tighten the screws.
Diagram Description: Shows the front half of the roof rack with four crossbars being attached using M6*16 screws and washers. [Front Arrow] indicates the front direction.
Parts Used: (16) M8*16 Button Head Socket Cap Bolts Screws, (16) M8*20*1 Flat Washer.
Step 11: Connect Front and Rear Sections
Finally, connect the front and rear sections using the connecting brackets. Use M6*12 screws and M6*16*1 washers and nuts for assembly. Each side requires two connecting brackets, and an inner connecting bracket should also be installed.
Diagram Description: Shows the front and rear sections of the roof rack being joined together by connecting brackets. Close-up views detail the attachment points using M6*12 screws, M6*16*1 washers, and M6 Flange Hex Lock Nuts.
Parts Used: (6) M6*12 Button Head Socket Cap Bolts Screws, (6) M6*16*1 Flat Washer, (6) M6 Flange Hex Lock Nuts.
Step 12: Installation Complete
The installation is complete. Enjoy your wonderful off-road life with this quality Hooke Road product!
