Corston Cambridge Outdoor Lighting Range

Ground Spotlight (inc. 24V)

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Brass collar x1
• Lamp body x1
• Glass lens with gasket x1
• Ground spike x1
• Cable x1

Installation Instructions:

1. Push the spike into the ground, ensuring it is stable. Consult a qualified electrician to connect the light to the mains power.
2. Unscrew the brass collar to remove the glass lens and spring. Insert the bulb.
3. Keeping the silicone gasket on the glass lens, replace the lens on top of the spring and screw the collar back on.
4. Important: Ensure the brass collar is tightened all the way, as this is necessary for the IP rating of the light.

Safety Notes:

• Lights should only be installed by a qualified electrician.
• All lights must be installed in dry conditions.
• Turn off electrical supply to the circuit before installation.

Ground Floodlight

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Brass collar x1
• Glass lens with gasket x1
• Lamp body x1
• Ground spike x1
• Cable x1

Installation Instructions:

1. Push the spike into the ground, ensuring it is stable. Consult a qualified electrician to connect the light to the mains power.
2. Unscrew the brass collar to remove the glass lens. Insert the bulb.
3. Once the bulb is installed, replace the glass lens, ensuring the thicker side of the rubber gasket faces the bulb. Then screw the brass collar back into place.
4. Important: Ensure the brass collar is tightened all the way, as this is necessary for the IP rating of the light.

Safety Notes:

• Lights should only be installed by a qualified electrician.
• All lights must be installed in dry conditions.
• Turn off electrical supply to the circuit before installation.

Wall Spotlight (inc. 24V)

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Anchor x2
• Wall screw x2
• Mounting plate x1
• Lamp body x1
• Glass lens with gasket x1
• Brass collar x1

Installation Instructions:

1. Drill two 6mm holes, set the anchors, and screw the mounting bracket to the wall using the screws provided. Consult a qualified electrician to connect the light to the mains power.
2. Place the light body over the mounting bracket and use the grub screws provided to fix it in place.
3. Unscrew the brass collar to remove the glass lens and spring. Insert the bulb.
4. Keeping the silicone gasket on the glass lens, replace the lens and screw the collar back on.
5. Important: Ensure the brass collar is tightened all the way, as this is necessary for the IP rating of the light.

Safety Notes:

• Lights should only be installed by a qualified electrician.
• All lights must be installed in dry conditions.
• Turn off electrical supply to the circuit before installation.

Wall Floodlight

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Anchor x3
• Wall screw x3
• Mounting base x1
• Lamp body x1
• Glass lens with gasket x1
• Brass collar x1

Installation Instructions:

1. Remove the grommet and cut off the tip.
2. Put the grommet back in its place and push the wires through it. Make sure the gasket is attached to the mounting base.
3. Drill three 6mm holes and set the anchors to attach the mounting base to the wall.
4. Consult a qualified electrician to make the electrical connections.
5. Use the grub screws provided to attach the light to the mounting ring.
6. Screw the ring onto the mounting base.
7. Unscrew the brass collar and remove the glass lens. Insert the bulb.
8. Once the bulb is connected, replace the glass lens with the thicker side of the rubber gasket facing the bulb.
9. Important: Ensure the brass collar is tightened all the way, as this is necessary for the IP rating of the light.

Safety Notes:

• Lights should only be installed by a qualified electrician.
• All lights must be installed in dry conditions.
• Turn off electrical supply to the circuit before installation.

IP68 Waterproof Straight Connector

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Connector x1
• Grommet x2

Note: Swap the grommets when using armoured cable.

Installation Instructions:

1. Connect the wires using the waterproof terminal.
2. Screw the clamps on.
3. Hide the connector and cable, for example, underground.

IP68 Waterproof Split T Connector

This product must be installed in dry conditions by a qualified electrician. Turn off electrical supply to circuit before installation.

Included Components:

• Connector x1
• Grommet x3

Note: Swap the grommets when using armoured cable.

Installation Instructions:

1. Connect the wires using the waterproof terminal.
2. Screw the clamps on.
3. Hide the connector and cable, for example, underground.