HAMNSKÄR Wash-Basin Mixer Tap

Product Information

This document provides assembly and installation instructions for the IKEA HAMNSKÄR wash-basin mixer tap.

For additional information and support, please visit www.IKEA.com.

Contents

• Tools and spare parts
• Illustration of product, parts and part numbers
• Product assembly

Safety and Compliance

[Info-icon] The installation must be carried out in accordance with industry regulations, specifically "Säker Vatteninstallation".

[Warning-icon] Switch off the main shut-off valve before changing the mixer tap.

This product is certified under TG 1363, 1913, and complies with EN 817 | EN 1717.

RSK Numbers: 8275783, 8275785

Technical Specifications

Recommended Operating Temperature: Max. 60°C

Maximum Operating Temperature: Max. 80°C

Recommended Operating Pressure: 1-5 bar

Maximum Operating Pressure: 0.5-10 bar

Connection Size: G3/8" (R10)

Parts List

The following parts are included:

• Part 126907: Tap body with spout
• Part 10095595: Cartridge
• Part 10091769: Aerator/Flow guide
• Part 10004087: Seal ring
• Part 10092255: Handle cap
• Part 10093113: Flexible hose (x2)
• Part 121844: Mounting bracket plate
• Part 121845: Mounting bracket plate
• Part 121846: Mounting bracket plate
• Part 10044928: Mounting bracket component
• Part 10046279: Mounting bracket component
• Part 10124727: Drain body
• Part 10128667: Drain seal
• Part 10124733: Drain stopper component
• Part 10128770: Drain stopper seal
• Part 10124748: Drain stopper component
• Part 10128669: Drain stopper seal
• Part 10124734: Drain stopper component
• Part 10128671: Drain stopper seal

Assembly Instructions

Step 1: Prepare for Installation

[Info-icon] Ensure the tap is correctly positioned. The required hole diameter in the worktop is Ø34-37 mm (Ø1 3/8" - 1 7/16").

[Warning-icon] Seal the open surfaces around the tap base with silicone sealant to prevent water from penetrating the worktop in case of leaks. Silicone sealant is not included. The sealant must be water- and mould-resistant and suitable for installation according to EN 15651-3, Class XS1.

Step 2: Mount the Tap Body

Insert the tap body (part 126907) through the sink opening. From underneath, attach the provided mounting hardware (parts 121844, 121845, 121846, 10044928, 10046279, 10093113) and tighten securely using a wrench. Ensure the pipe connection is flat and free from sharp edges.

[Info-icon] Important: Do not overtighten, as this can damage hoses or washers.

Step 3: Final Tightening

Use a wrench to firmly tighten the mounting nuts from underneath the sink to secure the tap.

Step 4: Pre-Use Flushing

Before initial use, unscrew the aerator/flow guide (part 10091769). Allow water to run freely for a few minutes to flush out any debris. Then, screw the aerator/flow guide back into place, ensuring it is tight enough to prevent removal by hand.

Step 5: Leak Check

[Info-icon] Periodically check the installation to ensure there are no leaks.

Sink Drain Assembly

The following steps describe the assembly of the sink drain stopper mechanism:

Step 1: Install Drain Body

Insert the drain body (part 10124727) into the sink's drain opening. Place the sealing washer (part 10128667) and secure with the locking nut.

Step 2: Attach Stopper Mechanism

Assemble the drain stopper components (parts 10124748, 10128669) and insert them into the drain body.

Step 3: Install Stopper

Insert the drain stopper (part 10124733, 10128770) into the drain assembly.

Step 4: Final Stopper Assembly

Place the final stopper component (part 10124734, 10128671) onto the drain assembly.