Beghelli UP LED CT Emergency Lighting System

Product Overview

The Beghelli UP LED CT is an emergency lighting fixture designed for reliable performance in various settings. This manual provides detailed instructions for installation, wiring, configuration, and operation.

Installation and Wiring

Section A: Mounting and IP Rating

The fixture is designed for easy mounting and offers IP40 protection in its standard configuration. For IP65 rated installations, specific IP65 caps must be used, ensuring the cable entry diameter is between 5-10mm.

Diagram A illustrates the mounting of the fixture and the IP rating.

Section B: Battery Connection

Connect the battery to the designated connector as shown in the diagram. Ensure correct polarity.

Diagram B shows the battery connection.

Section C & C1: IP65 Cap Installation

For IP65 protection, install the IP65 caps, ensuring the cable used is Ø 5-10mm.

Diagram C and C1 detail the installation of IP65 caps.

Section D: Wiring Configurations

The fixture supports different wiring configurations for autonomous (SA) and maintained (SE) emergency lighting, with options for manual setting or central control via the CableCom Connect unit (cod. 20151).

Basic Setting (1h-3h) without App/Central: Allows for basic autonomy settings without external control.
Wiring with Infinity Mode Deactivated: Standard wiring for emergency lighting.
Wiring with Infinity Mode Activated: Enables advanced features when used with the CableCom Connect system.

Wiring Schematics:

Schema 1.1 (SA - Autonomous): For standalone emergency operation.
Schema 1.2 (SE - Maintained): For emergency operation where the light remains on during normal power.
Schema 2.1 (SA-SE): For combined autonomous and maintained operation, entering emergency mode upon general or local power failure.
Schema 2.2 (SA-SE): For combined operation, entering emergency mode upon general power failure.

Important Notes:

Maximum 32 lamps can be connected.
Do not connect other devices to the power cable/BUS (L+ N-).
Ensure correct phase and neutral polarity.
For central configuration, batteries must be sufficiently charged.

Diagram D illustrates various wiring configurations and connection terminals.

Configuration and Commands

The UP LED CT can be configured and controlled in several ways:

AT (without APP and Central): Basic settings and local control via a jumper or device settings.
AT + APP (B.connect): Configuration and control using the B.connect smartphone application.
AT + CableCom Connect Central + APP: Advanced centralized control and configuration via the CableCom Connect unit and the B.connect app.

Autonomy Settings: The fixture supports autonomy durations of 1h, 1.5h, 2h, 3h, and 8h. These can be set locally or via the app/central unit.

SE/SA Setting: This setting, applicable to SA (Maintained) luminaires, determines the operational mode.

Infinity Mode: When activated, the N2 L2 terminals must be connected as per schemas 2.1 or 2.2. With Infinity mode active and wired correctly, the autonomy is infinite when the CableCom network is present.

App B.connect Usage:

Download the B.connect app from the App Store or Google Play.
Access the luminaire configuration through the "luminaire" menu.

Lamp Response:

Fast flashing: Function executed.
Slow flashing: Function not enabled.
No flashing: Command not received.

Central CableCom Connect (cod. 20151): All configurations and commands can be sent remotely via the "nuBe" cloud.

Lamp Positioning for App Coverage: Ensure adequate proximity for the app to communicate with the lamp (e.g., within 50cm for strong light conditions).

Diagrams illustrate app usage and lamp positioning for communication.

Automatic Tests and LED Signals

Automatic Test Periodicity:

Functional Test (30 sec): Every 28 days.
Autonomy Test (1h): Every 26 weeks.

LED Signals:

Fixed Green: Battery charged.
Flashing Green: Battery charging.
One Red Flash: Battery error duration.
Two Red Flashes: Lighting LED error.
Three Red Flashes: Battery disconnected.

Communication Opening from App:

Remove and reapply power for less than 3 seconds to open communication.
Communication remains open for 2 hours, indicated by an orange flashing LED.
Functional Test and Functional STOP Test can be controlled via the B.connect App without opening communication.

Diagrams illustrate LED signals and app communication procedures.

Technical Specifications and Warnings

Models: 4370 SE, 4371 SE, 4372 SE/SA, 4373 SE/SA.
Power: 230V - 50Hz.
Battery Type: LTO 4.8V with capacities of 0.5Ah or 1Ah.
Expansion Modules: LG, LGFM, DALI modules are available.

Warnings and Guarantee:

This device is intended for its designed purpose only. Any other use is considered improper and dangerous.
Rechargeable batteries and LED sources are non-replaceable. Contact an authorized service center for repairs, using only original spare parts. Failure to comply may compromise safety.
Caution: Electric shock.

This product complies with Directive 2012/19/EU.

	Beghelli Formula 65 LED AT Emergency Lighting Installation and Operation Manual Comprehensive guide for the Beghelli Formula 65 LED AT emergency lighting fixture, covering installation, configuration, operation with the B.connect app, and troubleshooting. Details include autonomy settings, LED signals, and safety warnings.
	Beghelli Formula 65 LED CT Emergency Lighting Fixture Installation Manual Detailed installation, wiring, configuration, and operation guide for the Beghelli Formula 65 LED CT emergency lighting fixture. Covers basic settings, advanced features with B.connect app and CableCom Connect system, technical specifications, and safety warnings.
	Beghelli Completa LED CT Emergency Luminaire Installation and Operation Guide Comprehensive guide for the Beghelli Completa LED CT emergency luminaire, covering installation, wiring, autonomy settings, and operational modes including Infinity mode and app control.
	Beghelli Acciaio Emergenza Emergency Lighting - Technical Specifications and Applications Detailed technical specifications, performance data, and application guidelines for the Beghelli Acciaio Emergenza emergency lighting luminaire. Features include ATEX compliance, various mounting options, and high-transmission micro-prismatic glass.
	Beghelli Lungalargaluce Extreme LED AT Opticom Installation and Operation Manual Comprehensive guide for the Beghelli Lungalargaluce Extreme LED AT Opticom, covering installation, Opticom function activation, ATEX application details, LED status indicators, and safety warnings. Includes multilingual instructions for various modules.
	Beghelli Completa LED TR Emergency Luminaire Installation and Technical Guide Installation and technical guide for the Beghelli Completa LED TR emergency LED luminaire. Details IP ratings (IP40, IP42, IP66), wiring, model specifications, operation, and safety warnings.
	Beghelli P236/258 LED Luminaires - Technical Specifications and Applications Detailed technical specifications, features, and application information for Beghelli P236/258 LED luminaires, including performance data, mounting options, and accessories. Suitable for retail, offices, and educational facilities.
	Beghelli Acciaio Extreme LED DALI: Installation and ATEX Compliance Guide This guide provides detailed installation, wiring, and safety instructions for the Beghelli Acciaio Extreme LED DALI luminaire, including specific information for ATEX classified environments (Zone 2 Gas, Zone 22 Dust) and DALI control system integration.