GDW Tow Bar for Renault Laguna Grandtour (2001-...)
Model Ref: 1304
EEC Approval: e6*94/20*0293*00
Technical Specifications:
- D Value: 7.9 KN
- S Value: 75 kg
- Max. Towing Capacity: 1500 kg
Manufacturer: GDW nv
Website: www.gdwtowbars.com
Installation Instructions
- Remove the inner coating from the trunk and the plastic part below the exhaust. Remove all plugs from the provided holes in the chassis.
- Place the mounting pieces (g) and (h) with points (B) onto the threaded holes in the rear chassis crossbeam. Insert bolts and washers, but do not tighten yet. Then, insert the raised washers at point (A) on the outside of the chassis beam and tighten hand-tight.
- At point (C), insert the tubes (e) into the square openings and drill these points with Ø10.5mm. Place bolts and washers from the inside of the trunk and fit the mounting corners (f) onto these bolts. Ensure points (D) of the mounting corners align with points (D) of the mounting plates (g) and (h). Insert bolts and tighten hand-tight.
- Next, place the tow bar between the mounting plates (g) and (h) so that points (e) and (e') align. Insert bolts and washers, and tighten everything firmly.
- Assemble (*) and place mounting plate (i) onto the cross-section profile of the tow bar. Insert bolts and washers and tighten firmly.
- Replace the trunk's inner coating and remount the plastic part.
Composition / Parts List
| Item | Description | Reference |
|---|---|---|
| 1 | Tow bar | Ref. 1304 |
| 1 | Ball T43L000 | (*) |
| 1 | Mounting plate (i) | (*) |
| 4 | Bolts M12x80 | (*) |
| 1 | Security shackle | (*) |
| 10 | Security washers M12 | (*-E-E') |
| 8 | Nuts M12 | (*-E) |
| 4 | Bolts M10x90 | (A-C) |
| 6 | Security washers M10 | (A-C-D) |
| 6 | Nuts M10 | (A-C-D) |
| 2 | Heightened washers (50x50x12x65mm) | (A) |
| 4 | Bolts M8x30 | (B) |
| 4 | Security washers M8 | (B) |
| 4 | Washers Ø25x8x2mm | (B) |
| 2 | Mounting tubes (e) | (C) |
| 2 | Washers 50x50x12x2mm | (C) |
| 2 | Bolts M10x30 | (D) |
| 6 | Bolts M12x35 | (E-E') |
| 1 | Mounting piece (g) | (A-D-E-E') |
| 1 | Mounting piece (h) | (A-D-E-E') |
| 2 | Mounting pieces (f) | (C-D) |
All bolts and nuts: quality 8.8
Torque Specifications
All bolts and nuts: quality 8.8
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 10.8 | 1.1 |
| M8 | 25.5 | 2.60 |
| M10 | 52.0 | 5.30 |
| M12 | 88.3 | 9.0 |
| M14 | 137 | 14.0 |
| M16 | 211 | 21.5 |
All bolts and nuts: quality 10.9
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 | 13.7 | 1.40 |
| M8 | 35.3 | 3.6 |
| M10 | 70.6 | 7.2 |
| M12 | 122.6 | 12.5 |
| M14 | 194 | 19.8 |
| M16 | 299.2 | 30.5 |
Notes
- For the maximum permissible towing mass, consult your vehicle's dealer or owner's manual.
- Remove any bitumen coating or anti-vibration material from the fastening points of the tow bar.
- When drilling, be careful not to damage any brake lines, electrical wiring, or fuel lines.
