GDW Tow Bar Installation Guide for Toyota Camry (2001-....)
GDW Reference: 1326
Vehicle Compatibility
This tow bar is designed for the Toyota Camry, model years 2001 onwards.
EEC Approval & Technical Specifications
EEC Approval Number: e4*94/20*0324*00
The document specifies towing capacity parameters:
- D-Value Calculation: D = (max. towing mass kg * max. towing mass kg) / (max. towing mass kg + max. towing mass kg) * 0.00981 ≤ 9.10 kN
- Maximum towing mass: 1700 kg
- Maximum vertical load (s/): 65 kg
Diagram Descriptions
Vehicle Image: The document includes an image of a Toyota Camry.
Assembly Diagram: A diagram illustrates the tow bar components and their attachment points on the vehicle chassis. Key mounting points are labeled A, B, and C, with specific mounting pieces labeled 'g' and 'h'.
Bumper Cut-out Diagram: A diagram shows the required cut-out dimensions for the vehicle's bumper. It indicates the area to be cut away ('hatched area'), the bumper itself ('B'), the lower rim of the bumper ('O'), and the middle of the bumper ('M').
Fitting Instructions
The following steps detail the installation process:
- Disassemble the bumper and permanently remove the metal buffer beam. Loosen the exhaust at the bottom and remove the towing rings and the heat shield.
- Place the tow bar with points (A) on the liberated screw-thread holes where the towing rings were attached. Remove any sealing tape from the furthest hole. Insert bolts and washers and tighten securely, ensuring the tow bar does not touch the exhaust.
- Attach mounting pieces (g) and (h) with points (C) to the provided bolts on the underside of the chassis beams. Insert washers and nuts. Points (B) align with provided drillings in the chassis beam underside (sealed with tape). Drill these holes through to the trunk with a ø10.5mm drill bit, then enlarge them in the trunk to ø17mm. Insert the heightened washer through the trunk and then insert bolts, washers, and nuts, tightening them firmly.
- Attach the heat shield with a tow bar bolt and make an incision in the bumper according to the enclosed sketch. Re-position the bumper.
- Assemble the component marked (*) and tighten everything firmly.
Composition (Parts List)
| Item | Description | Quantity | Attachment Reference |
|---|---|---|---|
| 1 | Tow bar reference 1326 | 1 | |
| 2 | Ball T45H004 | 1 | |
| 3 | Bolts M12x70 | 2 | (A) |
| 4 | Bolts M12x60 | 2 | (A) |
| 5 | Security nuts M12 | 4 | (A-B) |
| 6 | Mounting slices T45 | 2 | (B) |
| 7 | Mounting tubes T45 | 2 | (B) |
| 8 | Socket plate P04 | 1 | (B) |
| 9 | Security shackle | 1 | (C) |
| 10 | Bolts M10x1.25x35 | 6 | (C) |
| 11 | Washers ø32x13x2.5 | 6 | (B-C) |
| 12 | Security washers M10 | 8 | (B-C) |
| 13 | Bolts M10x100 | 2 | (B) |
| 14 | Nuts M10 | 2 | (B) |
| 15 | Heightened washers 68mm | 2 | (B) |
| 16 | Security washers M8 | 2 | (C) |
| 17 | Nuts M8 | 2 | (C) |
| 18 | Mounting piece (g) | 1 | (B-C) |
| 19 | Mounting piece (h) | 1 | (B-C) |
Torque Specifications
All bolts and nuts are quality 8.8 unless otherwise specified.
| Bolt Size | Torque (Nm) | Torque (kgm) |
|---|---|---|
| M6 (Quality 8.8) | 10.8 Nm | 1.1 kgm |
| M8 (Quality 8.8) | 25.5 Nm | 2.60 kgm |
| M10 (Quality 8.8) | 52.0 Nm | 5.30 kgm |
| M12 (Quality 8.8) | 88.3 Nm | 9.0 kgm |
| M14 (Quality 8.8) | 137 Nm | 14.0 kgm |
| M16 (Quality 8.8) | 211.0 Nm | 21.5 kgm |
| M6 (Quality 10.9) | 13.7 Nm | 1.4 kgm |
| M8 (Quality 10.9) | 35.3 Nm | 3.6 kgm |
| M10 (Quality 10.9) | 70.6 Nm | 7.20 kgm |
| M12 (Quality 10.9) | 122.6 Nm | 12.5 kgm |
| M14 (Quality 10.9) | 194 Nm | 19.8 kgm |
| M16 (Quality 10.9) | 299.2 Nm | 30.5 kgm |
Important Notes
- For the maximum permissible towing mass for your vehicle, consult your vehicle dealer or owner's manual.
- Remove any bitumen coating or sound deadening material from the fastening points before installation.
- When drilling, exercise caution to avoid damaging any brake lines, electrical wiring, or fuel lines.
