JABLOTRON JA-110N-DIN PG Bus Power Module for DIN Rail
This document provides installation instructions and technical specifications for the JABLOTRON JA-110N-DIN module.
Introduction
The JA-110N-DIN is a PG bus power module designed for DIN rail mounting. It is part of the JABLOTRON system and features an output PG power relay that can control lighting, fans, or other devices. Installation of this module must be performed by a qualified technician holding a valid certificate issued by an authorized distributor.
Installation
⚠️ Electrical connections are reserved for qualified technicians.
When connecting the module to the system bus, always disconnect the power supply.
- Install the module on the DIN rail.
- Connect the bus cable to terminals (1).
- Test the module's operation by pressing the button (4). Upon powering up the module, the red RELAY LED (2) will illuminate.
- Connect the controlled device to the output terminals (5).
Note: If communication is lost, the yellow STATUS LED (3) will indicate this condition, and after 60 seconds, the relay will revert to its resting state.
Module Diagram
Figure 1: Description of the product's external parts:
- 1 - Bus terminals
- 2 - Relay trigger indicator LED
- 3 - Fault indicator LED
- 4 - Learning/Manual trigger button
- 5 - Relay terminals
System Enrollment and Parameters
Depending on the control panel type, use the recommended software or application. Refer to the control panel's manual for details.
Technical Specifications
| Feature | Specification |
|---|---|
| Power Source | From the 12 V (9-15 V) control panel bus |
| Quiescent Current (Relay OFF) | 5 mA |
| Maximum Current Consumption (Relay Activated) | 45 mA |
| Relay Contact Load (Galvanically and solidly separated from the bus) | |
| Maximum Switched Voltage | 250 V AC / 24 V DC |
| Resistive Load (cos φ = 1) | max. 16 A |
| Inductive, Capacitive Load (cos φ = 0.3) | max. 6 A |
| Halogen Lighting | max. 1000 W |
| DC Continuous Current | 384 Ω |
| Minimum Switched DC Output | 0.5 W |
| Power Dissipation | 1.6 W |
| Power Dissipation for Panel Heating | 1.9 W |
| Connected Wire Diameter | max. 2 x 1.5 mm²; 1 x 2.5 mm² |
| Environment | Indoor general |
| Operating Temperature Range | -10 °C to +40 °C |
| Operating Humidity | 75% RH, non-condensing |
| Dimensions | 18 x 90 x 64 mm (according to EN 60715) |
| Weight | 65 g |
| Certification Body | Trezor Test sro (No. 3025) |
| Conformity | EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000 |
Compliance and Disposal
JABLOTRON a.s. hereby declares that the product JA-110N-DIN is in compliance with the relevant European Union harmonization legislation: Directives No. 2014/35/EU, 2014/30/EU, and 2011/65/EU, when used as intended. The original Declaration of Conformity is available at www.jablotron.com, section Downloads.
Note on Disposal: Proper disposal of this product helps preserve valuable resources and prevent potential negative effects on human health and the environment from waste mismanagement. Please return the product to your retailer or contact your municipality for the nearest collection point.
For an electronic version of this manual (available in other languages) or a version for installation in the JA-100+, scan the QR code provided.
JABLOTRON a.s.
Pod Skalkou 4567/33
46601 Jablonec nad Nisou
Czech Republic
Tel.: +420 483 559 911
Internet: www.jablotron.com
