Hikvision Video Intercom Villa Door Station (DS-KV61X3-(W)PE1(C))

1. Appearance

The villa door station features the following components:

• 1 Microphone
• 2 Camera
• 3 Indicator
• 4 Button
• 5 Card Reading Area
• 6 Loudspeaker
• 7 Terminals
• 8 Debugging Port (for debugging only)
• 9 TAMPER
• 10 Set Screw
• 11 TF Card Slot
• 12 Network Interface

Indicator Description:

• Unlock: Green light
• Call: Orange light
• Communicate: White light

2. Terminal and Wiring

The terminal functions are as follows:

• NC: Door Lock Relay Output (Normally Closed)
• NO: Door Lock Relay Output (Normally Open)
• COM: Common Interface
• AIN1: For access of Door Contact
• AIN3: For access of Exit Button
• AIN2 & AIN4: Reserved
• 485-: RS-485 Interface (Reserved)
• 485+: RS-485 Interface (Reserved)
• 12 VDC IN: Power Supply Input
• GND: Grounding

Note: The RS-485 terminal is not supported.

3. Installation Accessory

Included accessories for installation:

• Mounting Template
• Mounting Plate (Dimensions: 102.58 mm x 39.24 mm x 6.2 mm)

4. Installation

The video intercom villa door station supports surface mounting.

Before You Start:

• Ensure all related equipment is powered off during installation.
• Required tools: Drill (ø2.846) and gradienter.
• It is recommended to purchase a protective shield before installation.

Surface Mounting without Protective Shield:

1. Stick the mounting template on the wall and drill screw holes according to the template. Remove the template.
2. Secure the mounting plate on the wall using the 4 supplied screws.
3. Install the villa door station onto the mounting plate and fix it with the set screw.

Note: Apply silicone sealant around the cable wiring area to prevent water ingress.

Surface Mounting with Protective Shield:

1. Stick the mounting template on the wall and drill screw holes according to the template. Remove the template.
2. Align the protective shield with the mounting template.
3. Secure the mounting plate and protective shield on the wall using the 4 supplied screws.
4. Install the villa door station onto the mounting plate and fix it with the set screw.

Note: Installation with a protective shield is advised for outdoor use.

Recommended Installation Height:

The distance between the camera and the ground should be between 1.4 m and 1.6 m. The optimal height is approximately 1.4 m, with a horizontal viewing angle of 129° and a vertical viewing angle of 75°.

5. Configuration via Web

1. Activate Device via Web:

The device must be activated by setting a strong password before use.

• Default IP Address: 192.0.0.65
• Default Port No.: 8000
• Default User Name: admin

1. Power on the device and connect it to the network.
2. Enter the IP address into your web browser and navigate to the activation page. (Ensure your computer and the device are on the same subnet).
3. Create and confirm a strong password.
4. Click OK to activate the device.

Note: Basic operations and remote configuration are unavailable until the device is activated.

2. Access Device via Web Browsers:

1. Enter the device's IP address in your browser's address bar and press Enter.
2. Enter the username and password, then click Login.

3. Communicate with Indoor Station:

1. Navigate to Settings -> Intercom -> Press Button to Call.
2. Set the call number for each button. You can also set a Call Management Center, which has higher privilege.
3. Press the button to call the indoor station.

4. Issue Card:

1. Navigate to Settings -> Access Control and Elevator Control -> Issue Card.
2. Present the card to the card reading area.
3. A confirmation window will appear upon completion.

Note: Supports M1 cards. Up to 10,000 cards can be managed.

5. Unlock Door:

Present an issued card to the card reading area to unlock the door.

Detailed Terminal and Wiring Descriptions

2.1 Terminal Description

The door station terminals include:

• Orange: RS-485+ (Reserved)
• Yellow: RS-485- (Reserved)
• Red: 12 VDC (Power Input)
• Black: GND (Grounding)
• White: AIN1 (Door Contact)
• White: AIN2 (Reserved)
• White: AIN3 (Exit Button)
• White: AIN4 (Reserved)
• Yellow: NC (Door Lock Relay Output NC)
• Green: COM (Common Interface)
• Blue: NO (Door Lock Relay Output NO)
• Black: GND (Grounding)

Note: The RS-485 terminal is not supported.

2.2 Wiring Description

2.2.1 Door Lock Wiring:

For magnetic locks or electric bolts, use the NC/COM terminals. For electric strikes, use the NO/COM terminals.

2.2.2 Door Contact Wiring:

Connect the door contact sensor to the AIN1 terminal.

2.2.3 Exit Button Wiring:

Connect the exit button to the AIN3 terminal.

1. Appearance

The network indoor station features:

• 1 Screen
• 2 Microphone
• 3 Debugging Port (for debugging only)
• 4 Network Interface
• 5 Loudspeaker
• 6 TF Card Slot
• 7 Alarm Terminal
• 8 Reserved
• 9 Power Terminal

Note: The appearance may vary by model.

2. Terminal and Wiring

The rear panel terminal includes:

• 2 RS-485 pins
• 5 Reserved pins
• 4 Relay output pins
• 8 Alarm input pins
• 1 GND pin

Note: The DS-KH6320-TE1 model has 11 reserved pins and 8 alarm input pins.

3. Installation

The indoor station supports wall mounting with two installation modes.

Installation Accessory Description:

Wall mounting plate and junction box are required. Junction box dimensions: 75 mm (width) x 75 mm (length) x 50 mm (depth).

Before You Start:

• Ensure the device and accessories are in good condition.
• The indoor station supports 12 VDC power supply.
• Ensure all related equipment is powered off during installation.
• Check product specifications for the installation environment.

Wall Mounting with Junction Box:

1. Chisel a hole in the wall (76 mm width x 76 mm length x 50 mm depth).
2. Insert the junction box into the hole.
3. Fix the wall mounting plate to the junction box with 2 screws.
4. Hook the indoor station onto the wall mounting plate. The lock catch will secure automatically.

Wall Mounting without Junction Box:

1. Insert 2 expansion tubes into the wall.
2. Fix the wall mounting plate with 2 screws.
3. Hook the indoor station onto the wall mounting plate. The lock catch will secure automatically.

4. Getting Started

1. Activate Indoor Station:

The device must be activated by setting a strong password.

1. Power on the device; it will enter the activation page.
2. Create and confirm a password.
3. Tap OK to activate.

2. Quick Configuration:

1. Choose Language and tap Next.
2. Set Network Parameters (Local IP, Subnet Mask, Gateway, or enable DHCP) and tap Next.
3. Configure Indoor Station Parameters:
   • Link to Main Door Station: Edit Floor and Room No., create/confirm SIP register password (must match door station's registration password).
   • Advanced Settings: Edit Community No., Building No., Unit No.
   • Link Indoor Extension: Edit No., Room Name, create/confirm SIP register password.
4. Link Related Devices: Devices in the same LAN will be displayed. Tap to link or enter the serial number.
5. Tap OK to save settings.
6. Tap Finish to save all settings.

Refer to the Video Intercom Network Indoor Station Configuration Guide and Operation Guide for details.

Product Overview

The KH6 series IP indoor station features a 7-inch touch screen for fluent video and audio communication. It simplifies deployment of the entire video intercom system, reducing time and cost. Users can view, chat with, and grant access to visitors remotely via mobile phone. It also integrates with other control systems like CCTV and elevator control.

Key Features:

• 7-inch TFT touch screen with 1024 x 600 resolution.
• Convenient Hik-Connect APP Mobile Control for remote access.
• Receive calls, open doors, and view live feeds remotely.
• Easy to use without a PC.
• Quick setup wizard.
• Configure the entire system via the touch screen.
• Live view of door stations and public area cameras.
• Supports voice messages for missed calls.
• Receives alarms via linkage with alarm systems.
• Supports elevator access control.