HIKVISION DS-KV61X3-(W)PE1(C) Video Intercom Villa Door Station

1 Appearance

The villa door station features the following components:

• Microphone
• Camera
• Indicator
• Button
• Card Reading Area
• Loudspeaker
• Terminals
• Debugging Port
• TAMPER switch
• Set Screw
• TF Card Slot
• Network Interface

Note: The debugging port is for debugging purposes only.

Indicator Description

• Unlock: Green indicator
• Call: Orange indicator
• Communicate: White indicator

2 Terminal and Wiring

The device has various terminals for connection:

• NC: Door Lock Relay Output (Normally Closed)
• NO: Door Lock Relay Output (Normally Open)
• COM: Common Interface
• AIN1: For the access of Door Contact
• AIN3: For the access of Exit Button
• AIN2 & AIN4: Reserved
• 485-: RS-485 Interface (Reserved)
• 485+: RS-485 Interface (Reserved)
• 12 VDC IN: Power Supply Input
• GND: Grounding

Note: RS-485 terminal is not supported.

Wiring Diagrams:

Figure 2-1 Terminal Description: Illustrates the connection points for all terminals including RS-485, power, ground, AIN inputs, and relay outputs (NC, NO, COM).

Figure 2-2 Door Lock Wiring: Shows connections for door locks. Terminal NC/COM is default for magnetic locks/electric bolts, while NO/COM is default for electric strikes.

Figure 2-3 Door Contact Wiring: Depicts the wiring for connecting a door contact sensor to AIN1.

Figure 2-4 Exit Button Wiring: Illustrates the connection for an exit button to AIN3.

3 Installation Accessory

The package includes:

• Mounting Template
• Mounting Plate (Dimensions: 102.58 mm x 39.24 mm x 6.2 mm)

4 Installation

The video intercom villa door station supports surface mounting.

Before You Start:

• Ensure all related equipment is powered off during installation.
• Required tools: Drill (ø2.846) and gradienter.
• It is recommended to purchase a protective shield before installation.

Surface Mounting without Protective Shield:

1. Stick the mounting template on the wall. Drill screw holes according to the template and then remove the template.
2. Secure the mounting plate on the wall using the 4 supplied screws.
3. Install the villa door station onto the mounting plate and secure it with the set screw.

Note: Apply silicone sealant around the cable wiring area to prevent water ingress. Refer to Figure A for visual guidance.

Surface Mounting with Protective Shield:

1. Stick the mounting template on the wall. Drill screw holes according to the template and then remove the template.
2. Align the protective shield with the mounting template.
3. Secure the mounting plate and protective shield on the wall using the 4 supplied screws.
4. Install the villa door station onto the mounting plate and secure it with the set screw.

Note: For outdoor installations, using a protective shield is advised. Refer to Figure B for the finished view.

Recommended Installation Height:

The recommended distance between the camera and the ground is 1.4 m to 1.6 m. The optimal height can vary based on user height. The horizontal field of view is 129°, and the vertical field of view is 75°.

Visual representation of height recommendations:

• Lowest height: 1.02 m (at 1.4 m camera height)
• Highest height: 1.78 m (at 1.4 m camera height)
• Lowest height: 1.12 m (at 1.5 m camera height)
• Highest height: 1.88 m (at 1.5 m camera height)
• Lowest height: 1.22 m (at 1.6 m camera height)
• Highest height: 1.98 m (at 1.6 m camera height)

5 Configuration via Web

5.1 Activate Device via Web

Activation requires setting a strong password. Default parameters:

• Default IP Address: 192.0.0.65
• Default Port No.: 8000
• Default User Name: admin

1. Power on the device and connect it to the network.
2. Enter the device's IP address into a web browser to access the activation page. Note: The computer and device must be on the same subnet.
3. Enter and confirm a strong password.
4. Click OK to activate.

Note: Basic operations and remote configuration are unavailable until the device is activated.

5.2 Access the Device via Web Browsers

1. Enter the device's IP address into the browser's address bar and press Enter to reach the login page.
2. Enter the user name and password, then click Login.

5.3 Communicate with Indoor Station

1. Navigate to Settings -> Intercom -> Press Button to Call.
2. Configure parameters: Edit call numbers for each button and set the Call Management Center if applicable. Note: The Call Management Center has higher priority than individual call numbers.
3. Press the button to call the indoor station.

5.4 Issue Card

1. Navigate to Settings -> Access Control and Elevator Control.
2. Click "Issue Card" and present the card to the card reading area.
3. A confirmation window appears upon completion.

Note: Only M1 cards are supported. Up to 10,000 cards can be managed. A voice prompt indicates when the limit is reached.

5.5 Unlock Door

After issuing cards, present an authorized card to unlock the door.

For detailed information, refer to the Video Intercom Villa Door Station User Manual (available via scanning a QR code).