Hikvision Villa Door Station & Indoor Station User Manual

DS-KV61X3-(W)PE1(C) Video Intercom Villa Door Station

This section details the installation, configuration, and wiring for the Hikvision DS-KV61X3-(W)PE1(C) Villa Door Station.

Diagram References

Appearance:

• 1. Microphone ?
• 2. Camera ?
• 3. Indicator Light
• 4. Button
• 5. Card Reading Area ?
• 6. Loudspeaker ?
• 7. Terminals
• 8. Debugging Port (for debugging only)
• 9. TAMPER switch
• 10. Set Screw
• 11. TF Card Slot
• 12. Network Interface ?

Indicator Description:

• Unlock: Green ✔️
• Call: Orange ?
• Communicate: White

Terminal and Wiring Description

Terminal Functions:

• NC: Door Lock Relay Output (Normally Closed)
• NO: Door Lock Relay Output (Normally Open)
• COM: Common Interface
• AIN1: For the access of Door Contact sensor
• AIN3: For the access of Exit Button
• AIN2 & AIN4: Reserved
• RS-485- : RS-485 Interface (Reserved)
• RS-485+ : RS-485 Interface (Reserved)
• 12 VDC IN: Power Supply Input
• GND: Grounding

Note: RS-485 terminal is not supported.

Installation Accessory

• 1. Mounting Template
• 2. Mounting Plate (Dimensions: 102.58 mm x 39.24 mm x 6.2 mm)

Installation

Note: Video intercom villa door stations support surface mounting.

Before You Start:

• Ensure all related equipment is powered off during installation.
• Tools required: Drill (ø2.846) and gradienter.
• Purchase a protective shield for outdoor installations.

Surface Mounting without Protective Shield

1. Place the mounting template on the wall and drill screw holes according to the template. Remove the template.

2. Secure the mounting plate to the wall using 4 supplied screws.

3. Install the villa door station onto the mounting plate and fix it with the set screw.

Note: Apply silicone sealant around the cable wiring area to prevent water ingress. (Refer to Figure A)

Figure A Description: Shows the Villa Door Station being mounted, with a callout for applying silicone sealant around the cable entry point.

Surface Mounting with Protective Shield

1. Place the mounting template on the wall and drill screw holes according to the template. Remove the template.

2. Align the protective shield with the mounting template.

3. Secure the mounting plate and protective shield to the wall using 4 supplied screws.

4. Install the villa door station onto the mounting plate and fix it with the set screw.

Note: For outdoor installations, using the protective shield is advised. (Refer to Figure B)

Figure B Description: Shows the Villa Door Station mounted with a protective shield, illustrating the final appearance.

Recommended Installation Height

The recommended distance between the camera and the ground is 1.4 m to 1.6 m. The optimal height may vary based on user height and desired coverage. The chart shows coverage at different angles (Horizontal 129°, Vertical 75°) with minimum reachable heights around 1.02m to 1.22m and maximums up to 1.78m to 1.98m.

Configuration via Web

1. Activate Device via Web

The device must be activated with a strong password before use.

Default Parameters:

• IP Address: 192.0.0.65
• Port No.: 8000
• User Name: admin

Activation Steps:

1. Power on the device and connect it to the network.
2. Enter the IP address (192.0.0.65) into your web browser's address bar and press Enter.
3. Create and confirm a strong password on the activation page.
4. Click OK to activate the device.

Note: Device cannot be used or configured remotely until activated.

2. Access the Device by Web Browsers

1. Enter the device's IP address into your web browser's address bar and press Enter to access the login page.
2. Enter the user name and password, then click Login.

3. Communicate with Indoor Station

1. Navigate to Settings -> Intercom -> Press Button to Call.
2. Configure parameters, including call numbers for each button and optionally set a Call Management Center.
3. Press the button on the door station to call the indoor station.

4. Issue Card

1. Navigate to Settings -> Access Control and Elevator Control.
2. Click Issue Card and present a card to the card reading area.
3. A confirmation window will appear upon successful issuance.

Note: Supports M1 cards. Up to 10,000 cards can be issued. A voice prompt indicates when the limit is reached.

5. Unlock Door

Present an issued card to the card reading area to unlock the door.

Detailed Wiring Diagrams

Terminal Description (Figure 2-1)

Terminal Connections:

Note: RS-485 terminal is not supported.

Door Lock Wiring (Figure 2-2)

This diagram illustrates connecting the door station's NC/COM terminals (for magnetic locks/electric bolts) or NO/COM terminals (for electric strikes) to the lock mechanism and a DC power source.

Door Contact Wiring (Figure 2-3)

This diagram shows how to connect a door contact sensor to the AIN1 terminal of the door station.

Exit Button Wiring (Figure 2-4)

This diagram illustrates connecting an exit button to the AIN3 and COM terminals of the door station.

DS-KH9510-WTE1(B) Video Intercom Network Indoor Station

The KH9 series IP indoor station features a 10-inch touch screen and Android system for fluent video and audio communication. It supports third-party application installation and includes the Hik-Connect app for integrated management of Hikvision devices.

Key Features:

• ? 10.1-inch colorful touch screen with 1024 x 600 resolution
• ? Built-in Android System
• Supports Android APP installation
• Supports third-party software integration
• Built-in Hik-Connect APP
• Facilitates all-in-one management of Hikvision's devices on tablet

Specifications

Physical Interface

Diagram Description: Shows front and back views of the DS-KH9510-WTE1(B) Indoor Station with numbered interfaces.

Available Model

• DS-KH9510-WTE1(B)

Accessory

Optional Accessories:

• DS-KAW50-1: A white, rectangular accessory box.
• DS-KAW50-1N: A green circuit board with electronic components.
• DS-KABH9510-T: A white, flat panel accessory.