Hykolity High Series LED Parking Lot Light
Contact: inquiry@hykolity.com | www.hykolity.com | +1 (562) 456-0507
Taglines: BRIGHT | TRUSTED | HIGH-QUALITY
Product Overview
This document provides detailed information on the Hykolity High Series LED Parking Lot Light, covering its advantages, applications, specifications, and installation procedures. The product is a high-performance LED lighting solution designed for parking lots and outdoor areas, featuring robust construction and energy-efficient operation.
[Image Description: Two dark-colored LED parking lot lights mounted on brackets, showcasing their design.]
Advantages
- Wattage is switchable.
- Utilizes Lumileds Chip with high CRI (Color Rendering Index).
- Input voltage range: 120-277VAC.
- Output constant current can be adjusted via a 0-10V cable.
- No UV or IR radiation in the beam.
- Easy to install and operate.
- Energy saving with a long lifespan.
- Certified by UL and CUL (UL Certified, Safety US-CA E495046).
- Instant start, with no flickering or humming.
- Green and eco-friendly, free from mercury.
Dimensions
Detailed dimensions are provided for different mounting configurations and wattages:
- ARM 150W/200W: Width: 11.8 inches, Height: 24.4 inches, Depth: 6.3 inches.
- ARM 240W/300W: Width: 11.8 inches, Height: 28.3 inches, Depth: 6.3 inches.
- SFM 150W/200W: Width: 11.8 inches, Height: 22.7 inches, Depth: 2.9 inches.
- SFM 240W/300W: Width: 11.8 inches, Height: 26.6 inches, Depth: 2.9 inches.
[Diagram Description: Side and front views illustrating the dimensions of the ARM and SFM models for both 150W/200W and 240W/300W configurations.]
Applications
This LED parking lot light is suitable for various outdoor applications, including:
- Outdoor basketball courts and tennis courts.
- Badminton courts and football fields.
- School playgrounds and stadiums.
- Community leisure entertainment plazas and general road lighting.
Specifications
| Feature | 150W/200W | 240W/300W | 5000K |
|---|---|---|---|
| Color Temperature | 5000K | ||
| Wattage | 150W/200W | 240W/300W | |
| Lumen | 22500LM/30000LM | 36000LM/45000LM | |
| Efficacy | 150LM/W | ||
| CRI | >80 | ||
| Lifespan | 50,000 hours+ | ||
| Distribution Pattern | Type III | ||
| Beam Angle | 155°x90° Degree Type III | ||
| Input Voltage and Frequency | 120-277VAC, 50/60Hz | ||
| PF (Power Factor) | >0.9 | ||
| THD (Total Harmonic Distortion) | ≤20% | ||
| Flicker Percent | <30% | ||
| Driver Surge Protection | L/N-PE: 6kV, L-N: 4kV | ||
| Dimming | 0-10V Dimmable | ||
| Sensor Type | Photocell | ||
| LED Type | SMD2835 | ||
| Housing | Die-cast Aluminum | ||
| Housing Color | Bronze | ||
| Waterproof Rating | WET (IP65) | ||
| Certification | DLC, UL Listed | ||
| Operating Temperature | -30°F ~ 122°F | ||
| Warranty | 5 Years | ||
Notice for User
- Please turn off power before installing or changing assembly parts.
- Ensure the input voltage and lamps are matched. After connecting the power line, make sure the wiring section is insulated.
- Non-professionals must not install or disassemble the lamps.
Troubleshooting
| Troubles | Check Points |
|---|---|
| Flickering of the light | Turn off the power and turn on again in 3 minutes. If the same phenomena occur, then contact the seller. |
| Out of working | Please check the connection. |
Installation Instructions
General Cautions
- Do not use an electric generator to test the LED Light.
- Please abide by related country, regional, and local laws and regulations when installing this fixture.
- To avoid electrical shock and damage, please do not install the lights in raining days.
General Notices
- To prevent from electric shock or fire risk, the installation must be conducted by an operator who has professional electrical knowledge.
- Please wear gloves to avoid injury before installing the Light.
- During or after installation, if there are situations such as smoke or fire in the wires or Light, please turn off the power immediately and notify relevant personnel for an overhaul.
- This light can be used for outdoor installation.
- Do not install in a hazardous environment. The ambient temperature must not exceed the rated operating temperature of the product.
- Do not install the product when it rains. Avoid the danger of lightning strikes and avoid accidents.
- External 0-10V only passive dimmers are supported.
General Wiring Diagram
The wiring diagram indicates the following connections:
- Black/Brown wires: ACL (Line)
- Green/Yellow wire: Ground
- White/Blue wires: ACN (Neutral)
- Dim+ and Dim- wires: For dimming control. Please check the light label for specific wire colors for DIM+ and DIM-.
Notice: Use the dimming+, dimming- (DC10V) marking leads to connect to an outside dimmer. This is Class 1 Wiring only. Please assure a cumulative leakage current of less than 3.5mA on the control circuit. The AUX control wire with shrinkable tubing shall not be damaged (no connection).
1. Slip Fitter Mounting (SFM)
Steps:
- Step 1: Loosen the four bolts on the AM bracket, connect the wires correctly, and pull the wires into the poles. [Illustration: Figure 5 shows the AM bracket with adjusting and locking bolts, connected to a support.]
- Step 2: Place the bracket into the pole and lock the four bolts. [Illustration: Figure 6 shows the light fixture mounted onto a pole support.]
Notice: The adjustable angle for SFM mounting is 0-90°.
2. Adjustable Arm Mounting (ARM)
Steps:
- Step 1: Fix the DM bracket to the square pole with a bolt, open the side lid of the DM bracket, pull the wire into the junction box, and connect the wires correctly. [Illustration: Figure 7 shows the DM bracket being attached to a square pole, with wires entering a junction box.]
- Step 2: Put the connected wire into the junction box, then cover the junction box. [Illustration: Figure 8 shows the junction box closed after wiring.]
Notice: The adjustable angle for ARM mounting is 0-35°. For round pole installation, please remember to remove the silicon plate when installing the fixture in a round pole. [Illustration: Figure 9 shows a round pole installation with a silicon plate.]
Special Functions Instruction: Wattage Adjustment
Follow these steps to adjust the wattage:
- Remove the 3/4 plug using a screwdriver.
- Adjust the internal wattage switch to set the desired wattage.
- Tighten the 3/4 plug after the adjustment is complete.
