Hykolity Guard Series LED Wall Pack Light
BRIGHT | TRUSTED | HIGH-QUALITY
Product Overview
The Hykolity Guard Series LED Wall Pack Light is designed for efficient and reliable outdoor illumination, offering superior brightness and durability.
Dimensions & Warranty
Advantages
- UL, cUL certified
- Features Lumileds 2835 LEDs with high CRI
- Input voltage range: 100-277VAC
- Adjustable output constant current lever via 0-10V dimming
- No UV or IR radiation in the light beam
- Easy installation and operation
- Energy-efficient with a long lifespan
- Provides soft, uniform light that is safe for eyes
- Instant start, no flickering, no humming
- Environmentally friendly design, mercury-free
Applications
- Entrance lighting
- Courtyard lighting
- Industrial lighting
- Outdoor landscape lighting
- Building illumination
- Hotel lighting
- General wall lighting
Notice for User
- Always turn off power before installing or changing any parts.
- Ensure the input voltage of the fixture matches the power supply.
- After connecting the power line, verify that the wiring section is properly insulated.
- Installation and disassembly should only be performed by qualified professionals.
Specifications
| Specification | Value |
|---|---|
| Power | 120W |
| Color Temperature | 5000K |
| Lumen | 16200LM |
| Efficacy | 135LM/W |
| CRI | >80 |
| Diffuser Type | PC |
| Beam Angle | 105 Degree |
| Input Voltage | 100-277VAC |
| Power Factor | >0.9 |
| THD | ≤20% |
| Flicker Percent | <30% |
| Driver Surge protection | L-N: 4kV, L&N-E: 6kV |
| Dimming | 0-10V dimming standard |
| Sensor Type | Photocell Sensor |
| LED Type | SMD 2835 |
| Housing | Die-cast aluminum |
| Housing Color | Bronze |
| Waterproof Rating | IP65 Grade |
| Operating Temperature | -40°F ~ 113°F |
| Lifespan | >50,000 Hours |
| Certification | UL Listed |
| Warranty | 5 Years |
Installation Guide
Installation Notes:
- For safety, installation personnel must possess professional electrical knowledge to prevent electrical shock or fire hazards.
- Wear protective gloves during installation to avoid injury.
- If smoke or sparks are observed during wiring, immediately turn off the power and contact relevant personnel.
- This fixture is designed for outdoor use. Ensure a minimum mounting height of 6.5ft from the ground.
Installation Steps:
- Step 1: Turn off the power supply. ?
- Step 2: Use a screwdriver to remove the screws located on both sides of the fixture.
- Step 3: Open the fixture, carefully disconnect the connection terminals, and remove the upper cover.
- Step 4: Use a screwdriver to remove the plug from the designated opening.
- Step 5: Drill the required mounting hole using an electric drill.
- Step 6: Attach the EVA cotton pad to the bottom shell of the fixture.
- Step 7: Thread the electrical wire through the bottom hole of the fixture.
- Step 8: Secure the bottom shell onto the mounting seat using screws.
- Step 9: Connect the Live (L), Neutral (N), and Ground (G) wires to the corresponding power supply terminals.
- Step 10: Install the fixture cover and connect the terminal block.
- Step 11: Confirm that the installation is complete and all connections are secure before turning on the power switch. ?
Standard Wire Identification:
- L/Live wire: Typically Black or Brown
- N/Null wire: Typically White or Blue
- Ground wire: Typically Green or Yellow-green
Warning: During the grounding process, ensure that the earth wire of the driver and the fixture housing are securely connected together with the earth wire of the local power supply.
Cautions:
- Do not use an electric generator to test the LED fixtures, as this may cause damage.
- Always comply with relevant country, regional, and local laws and regulations during installation.
- Avoid installing the fixture during rain to minimize the risk of electric shock and prevent potential failures.
