Hykolity Libra Series LED Strip Light
Bright. Trusted. High-Quality.
Contact: inquiry@hykolity.com | Website: www.hykolity.com | Phone: +1 (562) 456-0507
Specifications
| Model | 2FT | 8FT |
|---|---|---|
| Color Temperature | 3500K/4000K/5000K | |
| Wattage | 15W/20W/25W | 65W/75W/90W |
| Efficacy | 130LM/W | |
| CRI | >80 | |
| Lifespan | 50,000 hours+ | |
| Input Voltage | 120-277VAC | |
| Power Factor | >0.9 | |
| Dimming | 0-10V Dimmable | |
| Housing | Sheet Metal Stamping | |
| Housing Color | White | |
| Certification | UL Listed | |
| Operating Temperature | 14°F ~ 104°F | |
| Warranty | 5 Years | |
Dimensions
The Libra Series LED Strip Light is available in 2FT and 8FT lengths.
2FT Model: Approximately 22.2 inches in length, 1.9 inches in height, and 2.5 inches in width.
8FT Model: Approximately 94.2 inches in length, 1.9 inches in height, and 2.5 inches in width.
Hardware Content
The following hardware components are included for installation:
- A: JUNCTION BOX BAFFLE (2 pieces)
- B: SCREW-4*6*8 (4 pieces)
- C: SELF-DRILLING SCREW-4*32*7 (2 pieces)
- D: PLASTIC TUBE-6*31mm (2 pieces)
- E: V-HOOK (2 pieces)
- F: CHAIN (2 pieces)
Installation Instructions
Important Safety Note: Always turn off the power supply from the main circuit breaker first!
General Warnings: To reduce the risk of death, personal injury, or property damage, read all warnings and instructions. Commercial installation should be performed by a qualified licensed electrician. Do not expose wiring to sharp edges. Do not alter enclosures.
General Cautions: Avoid direct eye exposure to the light source. Keep small parts away from children. Allow fixture to cool before handling.
Notice: Minimum 90° supply conductors. Suitable for Dry or Damp locations.
General Wiring Diagram: Connect Black (Line) to Purple (Dim+) and Blue (-). Connect White (Neutral) to Pink (Dim-) and Red (+). Connect Green (Ground) to the ground wire. Dimming wires connect to a 0-10V compliant control.
Surface Mounting
- Take out the light fixture and accessories package from the box.
- Fix the baffle on the lamp.
- Open the module board down. Press the part between the narrow rectangular hole and the snaplock to release it.
- Fix the lamp to the ceiling using appropriate plastic anchors and screws (not included).
- Wire the fixture to the main power supply through the junction box.
- Assemble the module board upwards. The installation is completed.
Chain Suspended Mounting
- Take out the light fixture and accessories package from the box.
- Connect the V-hook to the lamp housing.
- Attach the chain to the V-hooks.
- Connect the AC wires (Line, Neutral, Ground).
- The installation is completed.
Field-Adjustable Wattage & CCT
Users can adjust the color temperature (CCT) and lumen output (wattage) using two DIP switches located on the side of the fixture.
Each DIP switch offers 3 options (left, middle, right), corresponding to 3 color temperatures and 3 power levels, allowing for customized lighting combinations.
Factory Default Settings:
CCT: 5000K
Wattage: 90W (8FT model); 25W (2FT model)
Adjustment Instructions:
- Locate the DIP switches on the side of the fixture.
- Select the desired wattage and color temperature by sliding the respective switches to the left or right.
