Safety Warnings
⚠️ CHOKING HAZARD
Small parts. Sharp points. Adult assembly required.
⚠️ DROWNING HAZARD
There is a risk of young children drowning around open containers of water. Adult supervision is always required.
⚠️ BURN HAZARD
Always check the temperature of the product before letting your children play with it. Remember that the product may cause burns if left in direct sunlight. Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.
General Safety Statement
Observe all statements and warnings to reduce the likelihood of serious or fatal injury. Save this sheet for future reference.
Safety Information
- Intended for use by children from ages 1-1/2 years and up.
- Adult assembly required.
- Provide continuous adult supervision at all times.
- Instruct children not to use product until properly assembled.
- Holds up to 5 gal. (18.92 l.) of water.
- Take indoors or do not use when the temperature drops below 32°F (0°C).
Product Care
Inspection
Inspect this product before each use. Tightly secure connections and replace damaged or worn components. Contact The Step2 Company for replacement parts.
Cleaning Instructions
General Cleaning: Use mild soapy water. Water should be changed frequently. Sanitize occasionally to remove organic debris and prevent bacterial growth.
Disposal Instructions
Please recycle when possible. Disposal must be in compliance with all government regulations.
Assembly Instructions
Parts Identification
Main Components:
- Part A: Base/Pond
- Part B: Legs (x3)
- Part C: Support Column
- Part D: Water Wheel/Mechanism Housing
- Part E: Shower/Top Structure
- Part F: Spinner
- Part G: Spinner Attachment
- Part H: Funnel/Pouring Spout
- Part I: Shower Head/Sprinkler
- Part J: Shower Arm Connector
- Part K: Shower Arm
- Part L: Crank Handle
- Part M: Crank Shaft
- Part N: Crank Handle Attachment
- Part O: Pouring Cup
- Part P: Fastener/Bolt
- Part Q: Washer
- Part R: Screw/Fastener
Fasteners:
- x4 | 1/2" (38.1 mm) screws
- x6 | 1-1/2" (3.81 cm) screws
- x6 | 1" (2.54 cm) screws
- x4 | 2-1/2" (6.35 cm) screws
Step-by-Step Assembly
Step 1: Attach Part B (Leg) to Part A (Base) using screws. The diagram shows three legs being attached.
Step 2: Repeat Step 1 for the remaining legs.
Step 3: Repeat steps to attach all legs.
- (English) Repeat steps to other legs.
- (French) Répétez les étapes sur les autres pieds.
- (Spanish) Repita los pasos en las otras patas.
- (Italian) Ripetere i passi da per le altre gambe.
- (Dutch) Herhaal stap bij de andere poen.
- (Portuguese) Repetir os passos para as outras pernas.
- (Polish) Powtórzyć kroki w stosunku do pozostałych nóg.
- (Chinese) 在其他条腿上重复步骤。
- (Arabic) كرر الخطوات من مع الأرجل الثلاثة الأخرى.
Step 4: Attach Part B (Leg) to Part A (Base) using screws. The diagram shows a leg being attached with screws.
Step 5: Repeat steps to attach all legs.
- (English) Repeat steps to other legs.
- (French) Répétez les étapes sur les autres pieds.
- (Spanish) Repita los pasos en las otras patas.
- (Italian) Ripetere i passi da per le altre gambe.
- (Dutch) Herhaal stap bij de andere poen.
- (Portuguese) Repetir os passos para as outras pernas.
- (Polish) Powtórzyć kroki w stosunku do pozostałych nóg.
- (Chinese) 在其他条腿上重复步骤。
- (Arabic) كرر الخطوات من مع الأرجل الثلاثة الأخرى.
Step 6: Assemble the water pump/mechanism. Insert Part P (Fastener) through Part Q (Washer) and then through Part A (Base) into the mechanism housing. The diagram shows hands assembling parts P, Q, and A.
Step 7: Insert the assembled Part P and Q into Part A (Base). The diagram shows the assembled P+Q being inserted into A.
Step 8: Insert Part R (Screw/Fastener) into the mechanism housing on Part A. The diagram shows Part R being inserted.
Step 9: Rotate Part R to secure the mechanism. The diagram shows a hand turning Part R.
Step 10: Insert the water pump mechanism into Part A. The diagram shows a hand pushing the mechanism into place.
Step 11: Attach Part D (Water Wheel/Mechanism Housing) to Part A. The diagram shows Part D being placed onto Part A.
Step 12: Secure Part D to Part A using screws. The diagram shows screws being inserted into Part D and A.
- Hold:
- (English) Hold
- (French) Prise
- (Spanish) Asimiento
- (Italian) Tenuta
- (Dutch) Greep
- (Portuguese) Preensão
- (Polish) Przytrzymaj
- (Chinese) 握住
- (Arabic) ثبت
Step 13: Insert Part C (Support Column) into Part A. The diagram shows Part C being inserted.
Step 14: Secure Part C to Part A using screws. The diagram shows screws being inserted into Part C and A.
- Hold:
- (English) Hold
- (French) Prise
- (Spanish) Asimiento
- (Italian) Tenuta
- (Dutch) Greep
- (Portuguese) Preensão
- (Polish) Przytrzymaj
- (Chinese) 握住
- (Arabic) ثبت
Step 15: Attach Part D (Water Wheel/Mechanism Housing) to Part E (Shower/Top Structure). The diagram shows D being attached to E.
Step 16: Attach Part C (Support Column) to Part E (Shower/Top Structure). The diagram shows C being attached to E.
Step 17: Connect the assembled top structure (E with C and D) to the base (A) using screws. The diagram shows screws being inserted to connect E to A via C.
Step 18: Secure the top structure to the base using screws. The diagram shows screws being inserted.
Step 19: Attach Part D (Water Wheel/Mechanism Housing) to Part E (Shower/Top Structure). The diagram shows D being attached to E.
Step 20: Attach Part C (Support Column) to Part E (Shower/Top Structure). The diagram shows C being attached to E.
Step 21: Insert Part H (Funnel/Pouring Spout) into the designated slot on Part A. The diagram shows H being inserted.
Step 22: Attach Part J (Shower Arm Connector) to Part K (Shower Arm). Then attach this assembly to Part A. The diagram shows J connecting to K, then the assembly being attached to A.
Step 23: Snap Part G (Spinner Attachment) onto Part F (Spinner). Then insert the spinner assembly into the mechanism on Part D. The diagram shows G snapping onto F, then inserted into D.
- Action: Snap
- (English) Snap
- (French) Emboîter
- (Spanish) Encájelo
- (Italian) Scatto
- (Dutch) Klikken
- (Portuguese) Encaixe
- (Polish) Zatrzasnąć
- (Chinese) 置入
- (Arabic) طبق
Step 24: Insert Part N (Crank Handle Attachment) onto Part M (Crank Shaft). Then insert the crank assembly into the mechanism on Part D. The diagram shows N onto M, then inserted into D.
- Action: Snap
- (English) Snap
- (French) Emboîter
- (Spanish) Encájelo
- (Italian) Scatto
- (Dutch) Klikken
- (Portuguese) Encaixe
- (Polish) Zatrzasnąć
- (Chinese) 置入
- (Arabic) طبق
Step 25: Snap Part O (Pouring Cup) onto Part L (Crank Handle). Then insert the crank assembly into the mechanism on Part D. The diagram shows O onto L, then inserted into D.
- Action: Snap
- (English) Snap
- (French) Emboîter
- (Spanish) Encájelo
- (Italian) Scatto
- (Dutch) Klikken
- (Portuguese) Encaixe
- (Polish) Zatrzasnąć
- (Chinese) 置入
- (Arabic) طبق
Step 26: Final assembly view of the completed water table.
Step 27: Insert Part I (Shower Head/Sprinkler) into the top structure. The diagram shows I being inserted into E.
Thank You
Thank you for purchasing the Step2® Rain Shower Splash Pond Water Table™. We'd appreciate a few minutes of your time to complete a brief survey so we can continue providing you with great products. To participate, please visit our website at: www.step2.com/survey/?partnumber=874600.
Thank you for your time, your friends at Step2.
