Assembly Instructions

Contact Information

Phone: 1-424-206-5666

Email: support@yuzhouint.com

Support Hours:

• EN: 1:00 PM to 1:00 AM GMT, Monday to Friday.
• DE: 14:00 - 02:00 Uhr (MEZ), von Montag bis Freitag.
• IT: Dalle 14:00 alle 2:00 CET, dal lunedì al venerdì.
• FR: De 14 h à 2 h (UTC+1), du lundi au vendredi.
• ES: De 14:00 a 02:00 horas (CET+1.), de lunes a viernes.

Warm Tips

• Carefully read and keep these instructions for later.
• Before assembling, ensure all parts and accessories are present.
• Assemble on a soft, smooth surface like a carpet to avoid scratches.
• Do not fully tighten the screws until everything is correctly in place.

Assembly Recommendations

We recommend using hand tools for assembly. If an electric screwdriver is used, reduce its power to protect the product.

Tip-over Restraint: Use of tip-over restraints may only reduce but not eliminate, the risk of tip-over.

Parts List

1: 1 pc

2: 1 pc

3: 1 pc

4: 1 pc

5: 1 pc

6: 2 pcs

7: 5 pcs

8: 4 pcs

9: 2 pcs

10: 1 pc

11: 1 pc

Hardware List

A: 12PCS

B: 12PCS

C: 8PCS (Φ8*30m)

D: 4PCS (Φ1/4"*2")

E: 1PC

F: 16PCS (Φ1/4"*1/2")

G: 20PCS

H: 4PCS

I: 24PCS (Φ3.5*14mm)

J: 2PCS

K: 4PCS (Φ3*12mm)

L: 12PCS

M: 12PCS (Φ3*16mm)

N: 4PCS

O: 4PCS (Φ3*16mm)

P: 4PCS

Q: 4PCS (Φ3.5*35mm)

R: 2PCS

S: 1PC

Assembly Steps

Step 1

Attach part 9 to part 8 using screws D (x2) and tool E. Repeat for the second part 9. Attach part 8 to part 3 using screws D (x2) and tool E. Repeat for the second part 8. Ensure all screws are tightened.

Step 2

Insert screws F (x4) into the designated holes on part 2. Attach part 2 to the assembled frame using screws F (x16) and tool E. Ensure all screws are tightened.

Step 3

Attach part 3 to part 2 using screws C (x4). Attach part 4 to part 3 and 2 using screws A (x4) and B (x4). Ensure all screws are tightened.

Step 4

Attach part 5 to part 4 using screws A (x2) and B (x2). Ensure all screws are tightened.

Step 5

Insert parts 6 into the slots on parts 3 and 4.

Step 6

Attach part 1 to the top of the assembled unit using screws A (x6) and tool S.

Step 7

Attach part 4 to the side of the unit using screws A (x6) and B (x6). Ensure all screws are tightened.

Step 8

Attach hinges (part H) to the doors (part J) using screws K (x2) and tool S. Attach the doors to the cabinet using screws L (x12), M (x12), N (x4), and O (x4) with tool S. Adjust screws on hinges for uniform door clearance.

Step 9

Insert shelf supports G (x20) into the pre-drilled holes inside the cabinet. Place shelves 7 onto the supports.

Step 10

Attach hinges H (x2) to the doors J (x2) using screws K (x2) and tool S. Attach the doors to the cabinet using screws I (x4) and tool S.

Step 11

Attach hinges H (x2) to the doors J (x2) using screws K (x2) and tool S. Attach the doors to the cabinet using screws I (x8) and tool S. Adjust screws on hinges for uniform door clearance.

Step 12

Attach part 1 to the top of the cabinet using screws I (x8) and tool S. Attach part 3 to the side of the cabinet using screws H (x2) and tool S.

Step 13

Secure the cabinet to the wall using screws N (x2), P (x4), and Q (x4) with tool S. Ensure the wall anchors are properly installed.

Step 14

Attach anti-tip straps R (x2) to the furniture and the wall using hardware N and P. Ensure the straps are securely fastened.

Final Check

Do not press hard on the table edge.