Dodge 1996-Up Grand Caravan Minivan: Car Audio Installation Guide
This guide provides essential information and instructions for installing aftermarket car audio components in the 1996-2000 Dodge Grand Caravan minivan.
Disclaimer: This manual is based on carefully documented research. Absolute accuracy is attempted but not guaranteed. Use this manual as a reference guide. Scosche, Inc. cannot be responsible for inconsistencies that may occur.
Vehicle Overview & Fitment Data
This document details speaker and head unit fitment for the 1996-2000 Dodge Grand Caravan Minivan. It includes dimensions for various audio components and specific installation notes.
Tuner / Cassette / Disc Player Dimensions
| Chassis Type | Mini | Stan | DIN | ISO DIN | Single DBL DIN | Radio EQ Stack | Updated Through |
|---|---|---|---|---|---|---|---|
| CHASSIS H | 1 3/4-2 | 2 | 2 | 2 | 3 7/8 | 3 | '97 |
| CHASSIS W | 7 1/8 | 7 1/8 | 7 1/8 | 7 1/8 | 7 1/8 | 7 1/8 | '98 |
| CHASSIS D | 4 3/4-5 1/2 | 5 7/8-6 11/16 | 5 7/8-6 11/16 | 5 7/8-6 11/16 | 5 7/8-6 11/16 | 5 7/8-6 11/16 | '99 |
| NOSE H | 1 5/8-1 3/4 | 1 5/8-1 3/4 | 2 3/8 | 1 11/16 | 3 3/4-4 | 7 1/2 | '2000 |
| NOSE W | 4 1/8-4 3/16 | 4 1/8-4 3/16 | 7 1/2 | 6 11/16 | 6 11/16-7 1/4 | 6 11/16 | |
| SHAFT SP. | 5 1/8-5 3/4 | 5 1/8-6 |
In-Dash Application Notes
Key codes for in-dash installation:
- KS: Indicates specific application notes apply.
Application Kit Model: FC1270, 1273, 1235 & FCJ1275
Harness Adaptor: CR01/R/AUB
Antenna Adaptor: N/A
In-Dash Installation Area Dimensions
| Depth | Max Depth | Width | Height | |
|---|---|---|---|---|
| CAVITY | 7 7/8" | 7 7/8" | 8" | 3 1/2" |
| DASH OPENING | 7 7/8" | 7 15/16" | 7 15/16" | 3 3/16" |
Type: CHRYSLER *
Dash Material: PLASTIC
Thickness: 1/8"
For Max Depth: [ ] REMOVE REAR SUPPORT [ ] MODIFY CAVITY
Amplifier/EQ Mounting Locations (Width x Height x Depth)
| Under/In Dash | Under Seat | Glove Box | Trunk/Cargo |
|---|---|---|---|
| 14" x 3" x 6" | Various |
Dimensions shown are inches. For inch/mm conversions refer to chart section.
Diagram: Dashboard and Door Speaker Fitment
Dashboard: Factory provisions are 5 3/4" 2-hole. Aftermarket: 4" K. K = SA1451. Speaker mounts with tabs only, in free air - no width or height to cavity.
Front Doors: Factory provisions are 5" x 7" Infinity (deluxe) system. Aftermarket: 5 1/4" K, 6 1/2" K, 5" x 7". K = SA68. See NOTE.
Front Door Cavity Dimensions: Width: 7 7/8", Height: 5", Depth: 3".
Note: Must be equipped with factory speakers/adapter to use SAU56.
Diagram: Rear Panel Speaker Fitment
Rear Side Panels (Van): Factory provisions are 6" x 9". Aftermarket: 5 1/4" K, 6 1/2" K, 6" x 9". K = SA69.
Rear Side Panel Cavity Dimensions: Width: 8 3/8", Height: 6", Depth: 3".
Rear Corner Panels (Van): Factory provisions are 2 1/2" Tweeter. Aftermarket: Tweeter K.
Rear Corner Panel Cavity Dimensions: Width: 2 1/2", Height: 2 1/2", Depth: 1 7/8".
Important Notes
* Note: A gap of about 3/16" exists between the factory radio and the dash piece. Scosche, Chrysler, Dodge, and Plymouth installation kits include spacers to correct this problem when the kit is installed.
Installation Legend:
- B: BACK UP PLATES REQUIRED.
- C1: CUT TRIM/PLASTIC (STRUCTURE).
- C2: CUT STEEL.
- D: BELOW DECK ONLY.
- D1: LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT).
- D2: CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK.
- D3: NARROW SURFACE, BELOW DECK ONLY.
- F1: MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING.
- F2: MODIFY DASH CAVITY AND/OR PANEL.
- K: INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED.
- K1: KIT MODIFICATIONS REQUIRED.
- K2: EXTENSION KIT RECOMMENDED.
- K3: WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO.
- K4: FABRICATE PANEL/BRACKETS.
- K5: WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER.
- KS: SCOSCHE KIT RECOMMENDED.
- N: NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED.
- P: PERFECT WITHOUT MODIFICATION.
- P1: MODIFY OR REMOVE POCKETS.
- P2: COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT).
- P3: PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT.
- R: REAR LOAD ISOMOUNT.
- U: UNDERDASH.
- W1: WITH POWER WINDOWS ONLY.
- W2: WITHOUT POWER WINDOWS ONLY.
Installation Instructions
Preliminary Steps:
- Disconnect the negative battery cable.
- Antenna: The factory antenna is located on the right front fender.
Radio Removal and In-Dash Installation
Note: The factory stereo provision is for a standard Chrysler mount radio. An installation kit is required for all aftermarket installations. Scosche recommends using FCJ1275, FC1270/1273, or 1235 for E.Q. installations.
- Extract (2) screws in the trim bezel from just above the radio. Pop out cover just above the cup holder and remove (2) screws from behind.
- Pull the radio trim bezel away from the dash, unplug the AC/heating control.
- Extract the (2) screws securing the radio to the dash, pull the radio from the cavity, disconnect the ground strap, unplug all connectors, and remove the radio.
Front Dash Speaker Installation
Note: The factory speaker provision is for a 5 1/4" 2-hole speaker.
- Carefully pry out on the inside windshield plastic pillar panels.
- Using a panel removal tool, carefully pry up on the speaker grille top dash panel. Unplug warning lights on the driver's side, and lift up and away from the dash to remove.
- Extract the (2) screws securing each speaker, pull the speaker out of the dash, unplug the leads, and remove.
Front Door Speaker Installation (Infinity Deluxe Sound System Only)
Note 1: The factory provision is for a 5" x 7" speaker mounted in a steel adapter.
Note 2: The grille still exists in the door panel for base models, but there is no speaker or speaker bracket in this location.
- Remove the screw cover and extract the screw behind the door release housing trim.
- Extract (1) screw from the air flow area at the top front corner of the door panel.
- Carefully pop out the power window/lock control panel, unplug, and remove.
- Extract (1) screw from behind the power window/lock control panel.
- Extract (1) screw from the door panel's armrest pocket.
- Carefully pry out around the perimeter with a panel removal tool to release the pop fasteners. Lift up on the panel, release the metal rod from the door opener, and remove the panel.
- Extract the (4) screws securing the speaker to the adapter, unplug, and remove.
Rear Side Panel Speaker Installation
Note: The factory provision is for 6" x 9" standard speakers.
- Carefully pry out on the speaker grille/fabric panel which runs along the bottom of the rear side windows. Fastening clips will release and remove the panel.
- Extract the (4) screws securing the speaker, unplug the leads, and remove.
Rear Pillar Tweeter Installation (Infinity Deluxe System Only)
Note 1: The factory provision is for a 2 1/2" tweeter.
Note 2: The grille still exists in the panel for base models, but there is no speaker in this location.
- Using a panel removal tool, carefully pry down on the rear (back) edge of the plastic ceiling panel to release the fasteners and remove the panel.
- Carefully pop up the bottom rear plastic sill panel.
- Remove the bolt holding the upper rear shoulder seat belt swivel.
- Left side: Open jack compartment, remove jack, and extract (2) screws.
- Pull inward on rear pillar panels to release spring clips and access tweeters.
- Slide tweeter out of bracket, unplug, and remove.
