ANKER

Charge Your Phone or Tablet

Connect your phone or tablet to the PowerCore Slim 10000 PD using its USB-A or USB-C ports.

[Diagram Description: Illustration showing the PowerCore Slim 10000 PD with a USB-A port and a USB-C port. A cable connects a smartphone to the USB-A port, and another cable connects a tablet to the USB-C port.]

Charge Your Bluetooth Earphones or Smart Watches

To charge devices like smart watches or Bluetooth earphones that require lower power, activate "trickle-charging" mode:

• Press the power button twice, or press and hold it for 2 seconds. The LED indicator will turn green.
• Charge your recommended devices (e.g., smart watches, Bluetooth earphones).
• To exit "trickle-charging" mode, press the power button once again.

[Diagram Description: Illustration showing the power button on the PowerCore Slim 10000 PD. An arrow indicates pressing the button twice or holding it for 2 seconds. A green LED indicator is shown.]

Recharge Your PowerCore

Recharge the PowerCore Slim 10000 PD using a PD charger (PD charger not included).

[Diagram Description: Illustration showing a USB-C cable connecting the USB-C port of the PowerCore Slim 10000 PD to a PD charger.]

Specifications

Important Safety Instructions

• Store the product in a cool and dry place.
• Do not store the product in a hot or humid environment.
• Using a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
• Operating temperature should be between 0°C to 45°C.
• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
• If the product is not used for long periods of time, charge and discharge it once every three months.
• When charging a device, the product may feel warm; this is a normal operating condition and should not be cause for concern.
• In normal conditions, battery performance will decline over several years.
• Do not dispose of the product in heat or fire.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping, or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
• Be aware that a discharged battery may cause fire or smoke; tape the terminals to insulate them.

Regulatory Information

Declaration of Conformity

Hereby, Anker Innovations Limited declares that the product type A1231 is in compliance with Directives 2001/95/EC, 2014/30/EU, and 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: www.anker.com.

Anker Innovations Limited, Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party: Company Name: Fantasia Trading LLC, Address: 9155 Archibald Avenue, Suite 202, Rancho Cucamonga, CA, 91730, US. Telephone: +1 (800) 988 7973.

IC Statement

This device complies with Industry Canada license - ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Customer Service

Warranty

18-month limited warranty.

Technical Support

Lifetime technical support.

For support, contact: support@anker.com

Customer Service Numbers:

• US: +1 (800) 988 7973 (Mon-Fri 9:00am - 5:00pm PT)
• UK: +44 (0) 1604 936200 (Mon-Fri 6:00 - 11:00 GMT)
• DE: +49 (0) 69 9579 7960 (Mo-Fr 6:00 - 11:00)
• China: +86 4000550036 (Mon-Fri 9:00 - 17:30)
• Japan: +81 03 4455 7823 (Mon-Fri 9:00 - 17:00)