ANKER

Introduction

This user manual provides essential information for operating your Anker PowerCore Slim 10000 PD portable charger. It covers charging your devices, recharging the power bank, specifications, and important safety instructions.

Charging Your Devices

The PowerCore Slim 10000 PD features multiple ports to charge your devices.

Charge Your Phone or Tablet

Connect your phone or tablet to the USB-A or USB-C port using a compatible charging cable. The device will begin charging automatically.

Charge Your Bluetooth Earphones or Smart Watches

For devices requiring lower power, such as Bluetooth earphones or smartwatches, use the special "trickle-charging" mode.

To enter "trickle-charging" mode: Press the power button ? twice or press and hold it for 2 seconds. The LED indicator ? will turn green. This mode is recommended for charging smartwatches or Bluetooth earphones.

To exit "trickle-charging" mode: Press the power button ? once again.

Recharging the PowerCore

Recharge your PowerCore Slim 10000 PD using a USB-C Power Delivery (PD) charger (PD charger not included).

Connect a USB-C PD charger to the USB-C input port on the PowerCore. The power bank will begin recharging.

Specifications

Important Safety Instructions

When using this product, basic precautions should always be followed, including the following:

• Store the product in a cool and dry place.
• Do not store the product in a hot or humid environment.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
• Operating temperature should be between 0°C to 45°C.
• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
• If the product is not used for long periods of time, recharge and discharge it once every three months.
• When charging a device, the product may feel warm; this is a normal operating condition and should not cause concern.
• Under normal conditions, battery performance will decline over several years.
• Do not dispose of the product in heat or fire.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping, or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
• Be aware that a discharged battery may cause fire or smoke; tape the terminals to insulate them.

Compliance Information

Declaration of Conformity

Anker Innovations Limited declares that product type A1231 complies with Directives 2001/95/EC, 2014/30/EU, and 2011/65/EU. The full text of the EU declaration of conformity is available at: www.anker.com.

Manufacturer: Anker Innovations Limited, Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Importer: Fantasia Trading LLC, 9155 Archibald Avenue, Suite 202, Rancho Cucamonga, CA, 91730, US. Telephone: +1 (800) 988 7973.

IC Statement

This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Customer Service and Warranty

For FAQs and more information, please visit: anker.com/support

Warranty: 18-month limited warranty.

Technical Support: Lifetime technical support.

Contact Anker:

• Email: support@anker.com
• US: +1 (800) 988 7973 (Mon-Fri 9:00am - 5:00pm PT)
• UK: +44 (0) 1604 936200 (Mon-Fri 6:00 - 11:00 GMT)
• DE: +49 (0) 69 9579 7960 (Mo-Fr 6:00 - 11:00)
• China: +86 4000550036 (周一至周五 9:00-17:30)
• Japan: +81 03 4455 7823 (月-金 9:00-17:00)

Follow Anker on social media:

• Facebook: @Anker
• Japan Facebook: @Anker Japan
• Germany Facebook: @Anker Deutschland
• Official Instagram: @AnkerOfficial
• Japan Instagram: @Anker_JP
• Google+: @Anker