WAC Lighting Silo X10 - LED Monopoint Installation Instructions
Model: MO-2010
Safety Instructions
IMPORTANT: NEVER attempt any work without shutting off the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the "[power-off]" position and unscrew the fuse(s) or switch "[power-off]" the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
- Place the wall switch in the "[power-off]" position.
CAUTION: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this fixture.
Installing Lamp (Fig. 1)
Fig. 1: Diagram shows the base plate and canopy components. The base plate has slotted holes for mounting screws. The canopy attaches to the base plate via three screws. The luminaire body can be rotated horizontally (350 degrees) and vertically (90 degrees) for aiming. Components labeled include Base Plate, Canopy, Base Plate Mounting Screws, and Canopy Mounting Screws.
- Loosen the three canopy screws, twist and separate the canopy cover from the base plate. (Keep screws on base plate)
- Remove a knock out from the base plate.
- Attach the base plate to the surface using slotted holes for mounting screws (supplied).
- Connect fixture wires to 120V AC power wire, with wire nuts (supplied).
- Connect ground wire to the green wire from fixture.
- Mount the canopy to the base plate by twisting key holes over three screws in base plate.
- Tighten screws to secure canopy.
- After the light is on, rotate the luminaire body horizontally or vertically to aim properly.
Replacing TIR Lens
Follow these steps to replace the TIR lens:
Fig. 2: Illustration of removing the front cap from the fixture, indicating it can be done with a screwdriver or fingernail.
- Use a screw-driver or finger nail on inside lips to gently pull out the front cap of the fixture. (See Fig. 2)
Fig. 3: Diagram illustrating the removal of the lens holder. It shows the lens holder, a lens holder removal slot on the fixture body, and the different lens types: Flood Lens (TIR-LUM6-F) and Narrow Flood Lens (TIR-LUM6-N). A painted edge is noted to protect from damage.
- Use a flat-tip screw-driver and gently pry in the lens holder removal slot to remove the lens holder. (See Fig. 3)
- Replace the Lens with the desired one.
- Align plastic tabs and reinstall the lens holder securely. Ensure the silicone guide is in place. (See Fig. 4)
Fig. 4: Exploded view of components for lens reinstallation: Front Cap, Lens Holder, TIR Lens, Fixture Body, and Silicone Guide Ring.
- Reinstall the front cap.
Accessories (Fig. 6)
Instructions for installing accessories:
Fig. 5: Illustration showing the removal of the front cap, similar to Fig. 2, to access the fixture for accessory installation.
- Use a screw-driver or finger nail to gently remove the front cap of the fixture. (See Fig. 5)
Fig. 6: Diagram showing the installation of accessories into the front cap. Components illustrated include the Front Cap, Lens Accessory (LENS-11), Cross Louver (LENS-11P-CRL), and Snoot (LENS-11-SNOOT).
- Install the accessory into the front cap. Note: accepts one lens or one glare control accessory. (See Fig. 6)
Fig. 7: Side view of the fixture with an accessory installed. Shows the Front Cap, Fixture Body, Cross Louver, and indicates the Protrusion of the front cap due to the accessory base.
- Reinstall the front cap onto the fixture. Note: the front cap will protrude off the front of the fixture by the thickness of the accessory base. (See Fig. 7)
