WAC Lighting Lucio LED Monopoint Installation Instructions

Safety Instructions

IMPORTANT: NEVER attempt any work without shutting off the electricity. ⚡️

• Read all instructions before installing.
• System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
• Go to the main fuse box or circuit breaker. Place the main power switch in the "OFF" position and unscrew the fuse(s) or switch "OFF" the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
• Place the wall switch in the "OFF" position.

AVERTISSEMENT (French): IMPORTANT: Coupez l'électricité avant TOUTE manipulation. Lisez toutes les instructions avant d'installer. Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l'électricité et les règlements locaux. Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l'interrupteur principal en Position d'arrêt (« OFF »). Placez l'interrupteur mural en position d'arrêt (« OFF »).

All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL listing of this fixture. ⚠️

Electrical Data

Installing Lamp (FIG.1)

1. Loosen the three canopy screws, twist and separate the canopy cover from the base plate. (Keep screws on base plate)
2. Remove the knockout marked with "WIRING HOLE" label from the base plate. [Not for use] knockout is also present but not intended for use.
3. Attach the base plate to the surface by using slotted holes for mounting screws (supplied).
4. Connect fixture wires to building wires. This fixture features electronic low voltage (ELV) or 0-10V dimming capabilities.
   • To utilize ELV, wire black (line hot) and white (line neutral) in accordance with dimmer specifications.
   • To utilize 0-10V dimming, wire 0-10V+ (dim+), 0-10V- (dim-), black (line hot), white (line neutral) in accordance with dimmer specifications.
   Green fixture wire to ground. ?
5. Align the wiring hole on the canopy to the one on the base plate and mount it by twisting key holes over three screws in base plate.
6. Tighten screws to secure canopy.
7. After the light is on, rotate the luminaire body horizontally or vertically to aim properly. ?

Diagram Description (FIG.1): The diagram shows the base plate, canopy, mounting screws, and wiring hole. It illustrates how the canopy attaches to the base plate and indicates aiming angles of 90° and 365°. A knockout labeled "WIRING HOLE" is shown, with another marked "[Not for use]".

Accessories

With the power off, follow steps below. Reference specification sheet for compatible accessories.

Glare Control Accessory Installation

1. Gently move front cap forward to remove it. One torsion spring will remain engaged while the other will slide out completely. (See Fig 2)
2. Insert glare control accessory through the front frame. (See Fig 3)
3. Reinstall front cap back in place. Ensure torsion spring securely goes back into spring slot on fixture. (See Fig 4)

Diagram Description (FIG.2, FIG.3, FIG.4): These diagrams illustrate the installation of a glare control accessory. FIG.2 shows the front cap being removed. FIG.3 depicts inserting the accessory into the fixture's front frame. FIG.4 shows the front cap being reattached, emphasizing the correct seating of the torsion spring.

Lens Accessory Installation

1. Gently move front cap forward to remove it. (See Fig 5)
2. Rotate lens holder with ears anticlockwise to remove it. (See Fig 6)
3. Replace existing lens with new lens. (See Fig 7)
4. Align the triangle mark on the lens holder to the one on the reflector holder, then rotate clockwise to lock it. (See Fig 8)
5. Reinstall front cap back in place. Ensure torsion spring securely goes back into spring slot on fixture. (See Fig 9)

Diagram Description (FIG.5, FIG.6, FIG.7, FIG.8, FIG.9): These diagrams detail the lens accessory installation. FIG.5 shows removing the front cap. FIG.6 illustrates removing the lens holder by rotating it. FIG.7 shows the lens replacement step. FIG.8 highlights aligning specific marks on the lens holder and reflector holder for correct orientation. FIG.9 shows the final step of reattaching the front cap.