WAC Lighting Silo X42 - LED Monopoint

Safety Instructions

IMPORTANT: NEVER attempt any work without shutting off the electricity.

• Read all instructions before installing.
• System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
• Go to the main fuse box, or circuit breaker. Place the main power switch in the "OFF" position and unscrew the fuse(s) or switch "OFF" the circuit breaker switch(es) that control the power to the fixture or room that you are working on.
• Place the wall switch in the "OFF" position.

CAUTION: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL/CUL listing of this fixture.

AVERTISSEMENT:

• IMPORTANT: Coupez l'électricité avant TOUTE manipulation.
• Lisez toutes les instructions avant d'installer.
• Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l'électricité et les règlements locaux.
• Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l'interrupteur principal en position d'arrêt (« OFF »).
• Placez l'interrupteur mural en position d'arrêt (« OFF »).

MISE EN GARDE: Toutes les pièces doivent être utilisées tel qu'il est indiqué dans ces instructions. Ne remplacez pas les pièces, n'en laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l'homologation ETL/CETL du luminaire.

Installing Fixture (Fig. 1)

Fig. 1 Description: This diagram illustrates the base plate and canopy components. Key elements include the base plate, canopy, base plate mounting screws, and canopy mounting screws. The fixture offers ±90° adjustment from the vertical position and 355° rotation.

1. Loosen the three canopy screws, twist and separate the canopy cover from the base plate. (Keep screws on base plate).
2. Remove a knock-out from the base plate. Install appropriate wire connector.
3. Attach the base plate to the surface using slotted holes for mounting screws (supplied).
4. Connect fixture wires to 120-277V AC power wire, with wire nuts (supplied). Dimmable with compatible electronic low voltage (ELV) or 0 - 10V dimmer.
5. Connect ground wire to the green wire from fixture.
6. Mount the canopy to the base plate by twisting key holes over three screws in base plate.
7. Tighten screws to secure canopy.
8. After the light is on, rotate the luminaire body horizontally or vertically to aim properly.

Note: All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the UL/CUL listing of this fixture.

Beam Angle Adjustment (Fig. 3)

Fig. 3 Description: This diagram shows the fixture body and front cap, illustrating the beam angle adjustment mechanism. Rotation of the front cap controls the beam angle.

1. Hold the fixture body with one hand and the front cap with another.
2. Grip the front cap with two fingers and rotate it gently clockwise or counter-clockwise until the desired beam angle is achieved.
3. Cease rotation when you feel resistance, as the beam angle is reaching its minimum or maximum.

Adjustment Indicators:

• Counter Clockwise: Increase beam angle
• Clockwise: Decrease beam angle

Accessories

Fig. 4 Description: This diagram shows how to rotate the front cap clockwise to disengage it.

1. With the fixture powered off and the front cap facing toward you, rotate the front cap clockwise just past the position where you feel a "click".

Fig. 5 Description: This diagram illustrates the removal of the front cap assembly.

2. Gently, while holding the fixture body secure, rock the front cap assembly back and forth while pulling it away from the fixture body to remove the front cap assembly.

Fig. 6 Description: This diagram shows the accessory holder slot and how to remove the accessory holder using a flat-tip screwdriver.

3. Use a flat-tip screwdriver to remove the accessory holder by rotating it counter-clockwise.

Fig. 7 Description: This diagram displays various accessory components including the Accessory Holder, LENS-25, LENS-25P-CRL, LENS-25-SNOOT, and the Front Cap.

Accessory Compatibility: The fixture accommodates one lens and one glare control accessory. Refer to the spec sheet for a list of compatible accessories.

4. Install accessories between the front cap and accessory holder. Tighten the accessory holder after accessories are installed.

Fig. 8 Description: This diagram shows how to align the front cap tabs with the fixture body slots and reinsert the front cap assembly. It also indicates the internal fixture lens positioned at the top.

5. Ensure the internal fixture lens is still at the top position, and lens holder slots align with fixture body slots.
6. Align the front cap tabs with the fixture body slots and insert the front cap assembly back into the fixture.
7. Once fully inserted, rotate the front cap assembly counter-clockwise past the “click” and to the desired beam angle.