HAGOR BrackIT® S-I TV Wall Mount Installation Guide
Model: BrackIT® S-I | Article Number: 8426
Important Safety Information
Caution!
Technical devices are of considerable value. Handle components carefully during installation and protect them if necessary.
If necessary, the installation area should also be secured. Falling parts can cause injuries and material damage.
The materials included in the scope of delivery may not be suitable for the special conditions at the installation site. Please check this in advance and replace them with suitable materials if necessary.
If you are unsure about the installation of the product or have any questions, please contact HAGOR Products GmbH or other trained specialists.
Scope of Delivery
The following parts are included:
- Part A: Wall mounting plate (1x)
- Part B: Screen mounting bracket (1x)
- Part C: Cover plate (1x)
- Part D: Cover plate (1x)
Hardware:
- Screw a: M4x20 (4x)
- Screw b: M6x25 (4x)
- Screw c: M8x25 (4x)
- Washer d: Ø8 (4x)
- Washer e: M6 (7x)
- Screw f: Ø10x61 (3x)
- Screw g: St6x70 (3x)
- Screw h: M6x8 (1x)
Tools may be required for installation, such as a screwdriver (?), wrench (⚙️), or drill (?️).
Installation Steps
Step 1a: Mounting to Wood Stud Wall
Description: This step details mounting the bracket to a wood stud wall. Ensure the wall is suitable for mounting. The diagram shows bracket A being attached to a wall stud. Specific screws and washers are indicated.
Procedure:
- Check the suitability of the wall before installation.
- Position bracket A against the wall stud.
- Secure bracket A using washers 'e' (7x) and screws 'g' (3x). The diagram indicates these screws are inserted through bracket A into the wood stud.
Step 1b: Mounting to Brick or Concrete Wall
Description: This step details mounting the bracket to a brick or concrete wall. Ensure the wall is suitable for mounting. The diagram shows bracket A being attached to a brick wall. Specific screws and washers are indicated.
Procedure:
- Check the suitability of the wall before installation.
- Position bracket A against the brick or concrete wall.
- Secure bracket A using screws 'f' (3x) and washers 'e' (7x). The diagram indicates these screws are inserted into the wall, likely requiring wall anchors (not explicitly listed as parts but implied by the context of concrete/brick mounting).
Step 2a: Mounting Screen Bracket to Flat Back Screen
Description: This step describes attaching the screen mounting bracket (Part B) to the back of a flat-screen television. The diagram shows bracket B being aligned with the VESA mounting holes on the back of a flat screen. Screws 'a/b/c' and washers 'd' are used.
Procedure:
- Align bracket B with the VESA mounting holes on the back of the flat screen.
- Secure bracket B using screws 'a' (4x), 'b' (4x), or 'c' (4x) along with washer 'd' (4x) as appropriate for your screen's mounting points.
Step 2b: Mounting Screen Bracket to Arched Back Screen
Description: This step describes attaching the screen mounting bracket (Part B) to the back of a television with an arched back. The diagram shows bracket B being aligned with the VESA mounting holes on the back of an arched screen. Screws 'a/b/c' and washers 'd' are used.
Procedure:
- Align bracket B with the VESA mounting holes on the back of the arched screen.
- Secure bracket B using screws 'a' (4x), 'b' (4x), or 'c' (4x) along with washer 'd' (4x) as appropriate for your screen's mounting points.
Step 3: Hang Up and Secure the Screen
Description: This step shows how to hang the screen, now equipped with bracket B, onto bracket A mounted on the wall, and then secure it. The diagram illustrates the screen bracket hooking onto the wall bracket and a locking mechanism being engaged.
Procedure:
- Carefully lift the screen with bracket B attached.
- Hook bracket B onto bracket A mounted on the wall.
- Secure the screen using part 'h' (1x) to lock it in place.
Step 4: Make Adjustments
Description: This step details how to adjust the screen's position and tilt after it has been mounted. The diagrams show arrows indicating adjustment points for hinge mobility and screen inclination.
Procedure:
- Adjust hinge mobility: Use the indicated adjustment points to modify the screen's movement range.
- Adjust inclination: Adjust the screen's tilt angle within the specified range (e.g., -5° to +12°).
Step 5: Mount Covers / Cable Management
Description: This step shows how to attach cover plates (Parts C and D) to conceal the mounting mechanism and manage cables. The diagram illustrates the placement of covers C and D.
Procedure:
- Attach cover plates C and D to the mounting assembly to cover the mechanism and organize cables.
Dimensions
The HAGOR BrackIT® S-I TV Wall Mount has the following dimensions:
- VESA mounting pattern: 200 mm x 200 mm
- Bracket height: 167 mm
- Adjustable width range: 64 mm - 226 mm
- Tilt adjustment: -5° to +12°
- Maximum load capacity: 25 kg
