Important Safety Information
Caution! Technical devices are of considerable value. You should therefore handle the components carefully during installation and protect them if necessary. If necessary, the installation area should also be secured. Falling parts can cause injuries and material damage. The materials included in the scope of delivery may not be suitable for the special conditions at the installation site. Please check this in advance and replace it with suitable materials if necessary. If you are unsure about the installation of the product or have any questions, please contact HAGOR Products GmbH or other trained specialists.
Scope of Delivery
The following parts are included in the delivery:
- A: Pole (4x)
- B: Pole Connector (2x)
- C: M8x16 Screw (16x)
- D: Ceiling/Floor Plate (4x)
- E1: Cover (4x)
- E2: Cover (4x)
- F: M8x80 Screw (8x)
- G: Screw (8x)
- H: M8x12 Screw (16x)
- I: Wall Mount Bracket (1x)
- J: Rail Adapter (4x)
- K: Screw (40x)
- L: Cover (8x)
- M: Cable Clip (8x)
- N: Screw (8x)
- O: M8x10 Screw (8x)
- P: Alu Rail (4x)
- Q: Screw (4x)
- R: VESA Arm (4x)
- W-A: Retaining Bolt (24x)
- M-A: Screw Set (8x)
- M-B: Screw Set (8x)
- M-C: Screw Set (8x)
- M-D: Screw Set (8x)
- M-E: Screw Set (8x)
- M-F: Square Washers (8x)
- M-G: Small Spacer (16x)
- M-H: Large Spacer (16x)
Tools required: [pencil] [screwdriver] [wrench] [hammer] [drill] [measuring tape] [ladder]
Installation Steps
Step 1: Marking and Drilling (Ceiling)
Mark the desired position on the ceiling. Ensure the maximum distance between mounting points is 800 mm. Prepare for drilling.
Note: Maximum distance 800 mm.
Required drill bit size: 12 mm (1/2 inch).
Step 2: Marking and Drilling (Floor)
Mark the desired position on the floor. Ensure the maximum distance between mounting points is 800 mm. Prepare for drilling.
Note: Maximum distance 800 mm.
Required drill bit size: 12 mm (1/2 inch).
Step 3: Screw in Retaining Bolts (Floor / Ceiling)
Screw the retaining bolts (W-A) into the prepared holes in the floor or ceiling.
Step 4: Connecting the Poles
Connect the pole sections (A1, A2) using the provided connectors (B) and screws (C).
Step 5: Mount Rail Adapters
Attach the rail adapter (J) to the pole (A).
Step 6: Installing Ceiling/Floor Plates
Attach the ceiling/floor plate (D) to the pole (A) using screws (F) and (G).
Step 7: Mount Units (Floor / Ceiling)
Mount the units (D) onto the poles (A). The tube length can be adjusted. Details for adjustment can be found on the last page.
Step 8: Attach the Cover (Floor / Ceiling)
Attach the covers (E1, E2) to the mounted structure.
Step 9: Mount the Alu Rails
Mount the Alu Rails (P) using parts (K, J, H).
Step 10: Attach the Cover (Right / Left)
Attach the covers (L) to the Alu Rails (P) using parts (K, N, O).
Step 11: Attach VESA Arms to the TVs
Attach the VESA arms (R) to the TV mounting structure. Ensure correct orientation (top).
Step 12a: Installation on a TV with Flat Back
[✓] Compatible with TVs with flat backs. Use screws (M-A, M-F) or (M-B, M-F) as appropriate.
[X] Not compatible with TVs with irregular backs in this configuration.
Step 12b: Installation on a TV with Irregular Back
[✓] Compatible with TVs with irregular backs. Use screw sets (M-C/M-D), (M-E) with spacers (M-G, M-H) and washers (M-F) as required.
[X] Not compatible with TVs with flat backs in this configuration.
Step 13: Hang up the Screens
Carefully hang the screens onto the mounted VESA arms.
Step 14: Secure the Screens
[!] Ensure the screens are securely fastened. Use the locking mechanisms (Q, 1, 2) to secure the screens to the mount.
Step 15: Cable Management
Route cables neatly along the Alu Rail (P) using the cable clips (M).
Dimensions
Total Height: 3000 mm
Pole Height (each): 1500 mm
Width: 1009 mm
Depth: 205 mm
VESA Compatibility: Minimum 200 mm - Maximum 800 mm
Other Dimensions: 120 mm, 37 mm, 87 mm, 840 mm
Optional: CPS Drilling Template (Item no.: 3224)
This section describes the steps for using the optional drilling template:
- Cut the pole to the desired length using a saw.
- Position the template and secure it.
- Repeat for other positions as needed.
- Drill holes with a 8 mm drill bit through the template.
