NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

✉ CustomerService@vevor.com

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.

PRODUCT PARAMETERS

ASSEMBLY PRECAUTIONS

1. Assemble needs to follow these instructions. Incorrect assembly can be a hazard.
2. Wear safety goggles and heavy-duty work gloves during assembly.
3. Do not assemble when tired or when under the influence of alcohol, drugs or medication.
4. Weight capacity and other product capabilities apply to a properly and completely assembled product only.
5. Keep the assembly area clean and well-lit.
6. Keep bystanders out of the area during assembly.
7. Requires two people for assembly.

USE PRECAUTIONS

⚠ WARNING: TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

1. This product is not a toy. Do not allow children to play with or approach this item.
2. Use as intended only. Do not sit or stand on the product.
3. Inspect before every use. Do not use it if parts are loose or damaged.
4. Use on flat, level, and hard surfaces only.
5. Do not exceed the listed weight capacity. Tighten all knobs securely before applying load. Be aware of dynamic loading! The sudden load movement may briefly create an excess load, causing product failure.

TOOLS REQUIRED

Allen Wrench (not included)

Allen Wrench (not included)

PARTS LIST (2 lower supports)

NOTE: Part not shown to actual size.

• Part A: Shelf (x1) - A long, flat rectangular piece.
• Part B: Support Bracket (x1) - A triangular support bracket with mounting holes.
• Part C: Support Bracket (x1) - A triangular support bracket with mounting holes.
• Part D: Wall Plugs (x4) - Cylindrical plastic anchors for wall mounting.
• Part E: Nuts (x4) - Hexagonal nuts for securing bolts.
• Part F: Screws (x4) - Flat-head screws for attaching brackets to shelf.

PARTS LIST (3 lower supports)

• Part A: Shelf (x1) - A long, flat rectangular piece.
• Part B: Support Bracket (x1) - A triangular support bracket with mounting holes.
• Part C: Support Bracket (x1) - A triangular support bracket with mounting holes.
• Part D: Support Bracket (x1) - A triangular support bracket with mounting holes.
• Part E: Nuts (x4) - Hexagonal nuts for securing bolts.
• Part F: Screws (x4) - Flat-head screws for attaching brackets to shelf.
• Part G: Screw Caps (x3) - Decorative caps for screw heads.
• Part H: Wall Screws (x6) - Screws with pointed ends and washers for wall mounting.

ASSEMBLY STEPS

1. Step 1: Lock the support frames on Top.

   Attach the support brackets (B and C for 2 supports, or B, C, and D for 3 supports) to the shelf (A) using screws (F) and nuts (E). Ensure the brackets are oriented correctly to support the shelf.

2. Step 2: Measure the distance between the support frame holes.

   Place the assembled shelf unit against the wall where it will be mounted. Measure the distance between the mounting holes on the brackets. These distances are labeled L1 and L2.

3. Step 3: Punch on the wall, the distance is L1 and L2.

   Mark the wall at the measured distances (L1 and L2) corresponding to the bracket mounting holes. Drill holes at these marks on the wall.

4. Step 4: Knock the plastic parts into the hole on the wall.

   Insert the wall plugs (D) into the drilled holes on the wall. Tap them gently with a hammer if necessary until they are flush with the wall surface.

5. Step 5: Screw the screw into the plastic parts, do not screw it to the bottom of the 10mm distance.

   Insert the appropriate screws (F or H depending on the parts list for 2 or 3 supports) through the bracket holes and into the wall plugs. Screw them in until they are snug but leave enough thread exposed to hang the shelf. A 10mm gap is suggested.

6. Step 6: Hang the Top on the screw.

   Carefully lift the assembled shelf and align the bracket holes with the screws protruding from the wall. Hang the shelf onto the screws.

7. Step 7: Tighten the screw.

   Once the shelf is securely hung, fully tighten all screws to ensure the shelf is firmly attached to the wall. If applicable, attach screw caps (G) for a finished look.

Cleaning

• For cleaning, wipe the surface with a damp (not wet) cloth or wipe dry with a clean lint-free cotton cloth.