ASSEMBLY INSTRUCTION PATIO FURNITURE SETS
Notice
1. Tighten screws to 50% before fully fixing. An Allen wrench ⚙️ is recommended over an electric drill.
2. Place the item on a flat ground to adjust and ensure stability.
3. Gradually tighten all screws.
4. If screws do not align with holes during assembly, loosen other screws to 50% and continue the assembly process.
5. If the item is unstable, loosen all screws, adjust on a flat ground, and retighten.
6. Note: Fully tightening some screws early may cause alignment issues. Holes are designed larger to aid screw adjustment.
Part List
| Part | Description | Quantity |
|---|---|---|
| A | Right Armrest | 3 pcs |
| B | Left Armrest | 3 pcs |
| C | Seat Single Chair | 2 pcs |
| D | Back Single Chair | 2 pcs |
| E | Front Side Single Chair | 2 pcs |
| F | Back Chair Frame | 1 pc |
| G | Seat Chair Frame | 1 pc |
| H | Front Side Chair Frame | 1 pc |
| I | Left Side Frame | 4 pcs |
| J | Right Side Frame | 4 pcs |
| K | Back Bench Frame | 2 pcs |
| L | Seat Bench Frame | 2 pcs |
| M | Front Side Bench Frame | 2 pcs |
| N | Back Right Bench Frame | 1 pc |
| O | Seat Right Bench Frame | 1 pc |
| P | Front Side Right Bench Frame | 1 pc |
| V | Back Left Bench Frame | 1 pc |
| W | Seat Left Bench Frame | 1 pc |
| X | Front Side Left Bench Frame | 1 pc |
| Y | Small Table | 1 pc |
| Z | Small Glass Table | 1 pc |
| AA | Top Frame Big Table | 1 pc |
| AB | Under Frame Big Table | 1 pc |
| AC | Support Big Table 1 | 1 pc |
| AD | Support Big Table 2 | 2 pcs |
| AE | Big Glass Table | 1 pc |
| AF | Back Chair Cushion | 3 pcs |
| AG | Seat Chair Cushion | 3 pcs |
| AH | Seat Bench Cushion | 4 pcs |
| AI | Back Bench Cushion | 4 pcs |
Hardware List
| Part | Description | Quantity |
|---|---|---|
| 1 | Bolt M6x90 | 6 pcs |
| 2 | Bolt M6x40 | 26 pcs |
| 3 | Bolt M6x30 | 122 pcs |
| 4 | Bolt M6x20 | 12 pcs |
| 5 | Washer M6 | 110 pcs |
| 6 | Plastic Feet | 28 pcs |
| 7 | Connector | 8 pcs |
| 8 | Allen Key | 3 pcs |
Carton Content
The following parts are typically found in the cartons:
- Carton 1 (example): K (x2), N (x1), V (x1), M (x2), P (x1), X (x1), AI (x3), I (x4), J (x4), Hardware
- Carton 2 (example): A (x3), B (x3), D (x2), E (x2), H (x1), AG (x2)
- Carton 3 (example): AA (x1), AB (x1), O (x1), W (x1), AE (x1), AH (x4), L (x2), AI (x1), AG (x1), Y (x1), AC (x1), AD (x2), Z (x1), F (x1), C (x2), G (x1), AF (x3)
Note: Actual carton contents may vary. Please check all boxes upon arrival.
Assembly Steps
STEP 1
Connect Back Chair Frame (F) & Seat Chair Frame (G) with Bolt (2), washer (5), Allen Key (8).
Illustration shows Back Chair Frame (F) being attached to Seat Chair Frame (G). Two bolts (2) and two washers (5) are used to connect these parts. The Allen Key (8) is shown for tightening. The diagram indicates 50% tightening.
STEP 2
Connect the Part from Step 1 & Front Side Chair Frame (H) with Bolt (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 1 with Front Side Chair Frame (H) being attached. Two bolts (3) and two washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 3
Connect the Part from Step 2 & Left Side Frame (I), Right Side Frame (J), with Bolt (3), washer (5), Allen Key (8).
Illustration shows the partially assembled chair with Left Side Frame (I) and Right Side Frame (J) being attached. Ten bolts (3) and ten washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 4
Connect the Part from Step 3 & Plastic Feet (6) with Bolt (3), Allen Key (8).
Illustration shows the partially assembled chair frame from Step 3. Four Plastic Feet (6) are being attached to the bottom corners using eight bolts (3). The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 5
Put the Seat Chair Cushion (AG) and Back Chair Cushion (AF) to Finish Chair.
Illustration shows the completed single chair with Seat Chair Cushion (AG) and Back Chair Cushion (AF) placed on the frame. The diagram indicates 100% tightening (for previous steps).
STEP 6
Connect Back Single Chair Frame (D) & Seat Single Chair Frame (C) with Bolt (2), washer (5), Allen Key (8).
Illustration shows Back Single Chair Frame (D) being attached to Seat Single Chair Frame (C). Two bolts (2) and two washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 7
Connect the Part from Step 6 & Left Armrest Frame (B) with Bolt (2), (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 6 with Left Armrest Frame (B) being attached. Two bolts (2), one bolt (3), and three washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 8
Connect the Part from Step 7 & Right Armrest Frame (A) with Bolt (2), (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 7 with Right Armrest Frame (A) being attached. Two bolts (2), one bolt (3), and three washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 9
Connect Right Armrest Frame (A), Left Armrest Frame (B) & Back Single Chair (D), Front Side Single Chair (E) with Bolt (1), (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 8 with Back Single Chair (D) and Front Side Single Chair (E) being attached. Two bolts (1), four bolts (3), and six washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 10
Connect the Part from Step 9 & Plastic Feet (6) with Bolt (3), Allen Key (8).
Illustration shows the partially assembled unit from Step 9. Four Plastic Feet (6) are being attached to the bottom corners using eight bolts (3). The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 11
Put the Seat Chair Cushion (AG) and Back Chair Cushion (AF) to Finish Single Chair.
Illustration shows the completed single chair with Seat Chair Cushion (AG) and Back Chair Cushion (AF) placed on the frame. The diagram indicates 100% tightening (for previous steps).
STEP 12
Connect Back Bench Frame (K) & Seat Bench Frame (L) with Bolt (2), washer (5), Allen Key (8).
Illustration shows Back Bench Frame (K) being attached to Seat Bench Frame (L). Two bolts (2) and two washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 13
Connect the Part from Step 12 & Front Side Bench Frame (M) with Bolt (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 12 with Front Side Bench Frame (M) being attached. Two bolts (3) and two washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 14
Connect the Part from Step 13 & Left Side Frame (I), Right Side Frame (J), with Bolt (3), washer (5), Allen Key (8).
Illustration shows the partially assembled bench section with Left Side Frame (I) and Right Side Frame (J) being attached. Ten bolts (3) and ten washers (5) are used. The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 15
Connect the Part from Step 14 & Plastic Feet (6) with Bolt (3), Allen Key (8).
Illustration shows the partially assembled bench frame from Step 14. Four Plastic Feet (6) are being attached to the bottom corners using eight bolts (3). The Allen Key (8) is shown. This step is repeated twice (x2). The diagram indicates 50% tightening.
STEP 16
Put the Seat Bench Cushion (AH) and Back Bench Cushion (AI) to Finish Bench.
Illustration shows the completed bench section with Seat Bench Cushion (AH) and Back Bench Cushion (AI) placed on the frame. The diagram indicates 100% tightening (for previous steps). This step is repeated twice (x2).
STEP 17
Connect Back Left Bench Frame (V) & Seat Left Bench Frame (W) & Front Side Left Bench Frame (X) with Bolt (2), (3), washer (5), Allen Key (8).
Illustration shows Back Left Bench Frame (V), Seat Left Bench Frame (W), and Front Side Left Bench Frame (X) being assembled. Two bolts (2), two bolts (3), and four washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 18
Connect the Part from Step 17 & Right Side Frame (J), with Bolt (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 17 with Right Side Frame (J) being attached. Five bolts (3) and five washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 19
Connect the Part from Step 18 & Left Armrest Frame (B) with Bolt (1), (2), (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 18 with Left Armrest Frame (B) being attached. One bolt (1), two bolts (2), two bolts (3), and five washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 20
Connect the Part from Step 19 & Plastic Feet (6) with Bolt (3), Allen Key (8).
Illustration shows the partially assembled unit from Step 19. Four Plastic Feet (6) are being attached to the bottom corners using eight bolts (3). The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 21
Put the Seat Bench Cushion (AH) and Back Bench Cushion (AI) to Finish Left Bench.
Illustration shows the completed left bench section with Seat Bench Cushion (AH) and Back Bench Cushion (AI) placed on the frame. The diagram indicates 100% tightening (for previous steps).
STEP 22
Connect Back Right Bench Frame (N) & Seat Right Bench Frame (O) & Front Side Right Bench Frame (X) with Bolt (2), (3), washer (5), Allen Key (8).
Illustration shows Back Right Bench Frame (N), Seat Right Bench Frame (O), and Front Side Right Bench Frame (X) being assembled. Two bolts (2), two bolts (3), and four washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 23
Connect the Part from Step 22 & Left Side Frame (I), with Bolt (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 22 with Left Side Frame (I) being attached. Five bolts (3) and five washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 24
Connect the Part from Step 23 & Right Armrest Frame (A) with Bolt (1), (2), (3), washer (5), Allen Key (8).
Illustration shows the assembly from Step 23 with Right Armrest Frame (A) being attached. One bolt (1), two bolts (2), two bolts (3), and five washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 25
Connect the Part from Step 24 & Plastic Feet (6) with Bolt (3), Allen Key (8).
Illustration shows the partially assembled unit from Step 24. Four Plastic Feet (6) are being attached to the bottom corners using eight bolts (3). The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 26
Put the Seat Bench Cushion (AH) and Back Bench Cushion (AI) to Finish Right Bench.
Illustration shows the completed right bench section with Seat Bench Cushion (AH) and Back Bench Cushion (AI) placed on the frame. The diagram indicates 100% tightening (for previous steps).
STEP 27
Put the Small Glass Table (Z) to Finish.
Illustration shows the Small Glass Table (Z) being placed. It has a circular top and a cylindrical base.
STEP 28
Connect Under Frame Big Table (AB) & Support Big Table 1, 2 (AC), (AD) with Bolt (4), washer (5), Allen Key (8).
Illustration shows the Under Frame Big Table (AB) being connected to two Support Big Table 1, 2 (AC, AD) using six bolts (4) and six washers (5). The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 29
Connect the Part from Step 28 & Top Frame Big Table (AA) with Bolt (4), Washer (5), Allen Key (8).
Illustration shows the assembly from Step 28 with the Top Frame Big Table (AA) being attached. Six bolts (4) and six washers (5) are used. The Allen Key (8) is shown. The diagram indicates 50% tightening.
STEP 30
Put the Big Glass Table (AE) to Finish.
Illustration shows the completed Big Glass Table (AE) with a circular glass top and a curved metal base. The diagram indicates 100% tightening (for previous steps).
STEP 31
Connect the Bench & Chair sections with Connector (7) by Hand.
Illustration shows multiple assembled bench (K, N, V) and chair (F) sections being joined together using eight Connectors (7). The connectors are shown being attached by hand.
STEP 32
Finish.
Illustration shows the fully assembled patio furniture set, comprising multiple chairs and bench sections arranged in a semi-circle around a central coffee table and a smaller side table. Cushions are in place on all seating units.
