Latitude Run 3-Piece Patio Furniture Assembly Instructions
General Assembly Notice
Note: 50% tighten before fixing all bolts.
Notice:
- 50% Tighten before fixing all screws. An Allen wrench is recommended instead of an electric drill.
- Place the item on a flat ground to adjust and make sure it remains stable.
- Tighten up all screws with tools gradually.
- If the screws are not aligned with holes during assembly, please loosen all the other screws to 50% and continue the assembly process.
- If the item is not stable, please loosen all the screws, adjust it on a flat ground and tighten up all screws again.
- Note: If one or some screws are fully tightened during assembly, chances are the others will not be aligned with holes. In addition, all the holes are designed to be relatively larger to provide more space for the adjustment of the screws.
Part List
| Part Label | Description | Quantity | Visual Description |
|---|---|---|---|
| A | Table Leg | 2pcs | [Diagram: Rectangular frame component, likely for the table base.] |
| B | Table Top | 1pc | [Diagram: Flat rectangular surface, likely the tabletop.] |
| C | Glass | 1pc | [Diagram: Flat rectangular pane, representing the glass top for the table.] |
| D | Right Armrest | 2pcs | [Diagram: Curved armrest component for the chair, designed for the right side.] |
| E | Left Armrest | 2pcs | [Diagram: Curved armrest component for the chair, designed for the left side.] |
| F | Seat | 2pcs | [Diagram: Base frame for the chair seat.] |
| G | Backrest | 2pcs | [Diagram: Frame component for the chair back.] |
| H | Seat Cushion | 2pcs | [Diagram: Padded cushion for the chair seat.] |
| I | Back Cushion | 2pcs | [Diagram: Padded cushion for the chair back.] |
Hardware List
| Hardware Label | Description | Quantity | Visual Description |
|---|---|---|---|
| 1 | Bolt 1/4"×40mm | 4pcs | [Diagram: Bolt with 1/4 inch diameter and 40mm length.] |
| 2 | Bolt 1/4"×35mm | 12pcs | [Diagram: Bolt with 1/4 inch diameter and 35mm length.] |
| 3 | Bolt 1/4"×45mm | 8pcs | [Diagram: Bolt with 1/4 inch diameter and 45mm length.] |
| 4 | Allen Wrench 4mm | 1pc | [Diagram: L-shaped hexagonal wrench.] |
| 5 | Nut | 4pcs | [Diagram: Hexagonal nut.] |
| 6 | Allen Wrench 4mm | 1pc | [Diagram: Another L-shaped hexagonal wrench, possibly for a different size or as a spare.] |
Carton Contents
- Part A: Table Leg (2pcs)
- Part B: Table Top (1pc)
- Part C: Glass (1pc)
- Part D: Right Armrest (2pcs)
- Part E: Left Armrest (2pcs)
- Part F: Seat (2pcs)
- Part G: Backrest (2pcs)
- Part H: Seat Cushion (2pcs)
- Part I: Back Cushion (2pcs)
- Hardware 1: Bolt 1/4"×40mm (4pcs)
- Hardware 2: Bolt 1/4"×35mm (13pcs)
- Hardware 3: Bolt 1/4"×45mm (9pcs)
- Hardware 4: Allen Wrench 4mm (1pc)
- Hardware 5: Nut (4pcs)
- Hardware 6: Allen Wrench 4mm (1pc)
[Diagram: Visual representation of all parts and hardware included in the carton, with quantities indicated.]
Assembly Steps
Step 1: Assemble Table Base
[Diagram: Shows two Part A (Table Legs) being attached to Part B (Table Top). Hardware 1 (Bolt), Hardware 5 (Nut), and Hardware 6 (Allen Wrench) are used. The diagram indicates 4x Hardware 1, 4x Hardware 5, and 1x Hardware 6 are used for this step.]
Attach the two Table Legs (Part A) to the Table Top (Part B). Use four Bolts (Hardware 1), four Nuts (Hardware 5), and the Allen Wrench (Hardware 6). Ensure 50% tightening.
Step 2: Prepare Chair Seat Frame
[Diagram: Shows Part C (Glass) being placed onto a component, possibly related to the chair seat frame.]
Place Part C (Glass) onto the designated component. (Quantity: 1pc of Part C).
Step 3: Prepare Chair Seat Base
[Diagram: Shows Part F (Seat) with a close-up view indicating the removal of a tube plug using Accessory 4 (Allen Wrench).]
Use Accessory 4 (Allen Wrench) to lift out the tube plug in Part F (Seat).
Step 4: Assemble Chair Frame
[Diagram: Shows the assembly of the chair frame. Part D (Right Armrest), Part G (Backrest), and Part F (Seat) are connected. Hardware 2 (Bolt) and Hardware 3 (Bolt) are used. The diagram indicates 3x Hardware 2, 2x Hardware 3, 1x Part D, 1x Part F, and 1x Part G are used for one chair.]
Assemble the chair frame by connecting the Right Armrest (Part D), Seat (Part F), and Backrest (Part G). Use three Bolts (Hardware 2) and two Bolts (Hardware 3) per chair. Repeat for the second chair.
Step 5: Assemble Chair Frame (Continued)
[Diagram: Shows the assembly of the chair frame, connecting Part E (Left Armrest) to the existing structure. Hardware 2 (Bolt) and Hardware 3 (Bolt) are used. The diagram indicates 3x Hardware 2, 2x Hardware 3, 1x Part E, 1x Part F, and 1x Part G are used for one chair.]
Attach the Left Armrest (Part E) to the chair frame. Use three Bolts (Hardware 2) and two Bolts (Hardware 3) per chair. Repeat for the second chair.
Step 6: Add Cushions
[Diagram: Shows the assembled chair with Part H (Seat Cushion) and Part I (Back Cushion) being placed onto it. The diagram indicates 1x Part H and 1x Part I are used per chair.]
Place the Seat Cushion (Part H) and Back Cushion (Part I) onto each assembled chair. Repeat for the second chair.
Final Assembly
[Diagram: Shows the fully assembled 3-piece patio furniture set: two chairs and one table.]
Your 3-piece patio furniture set is now complete.
