Latitude Run 6-Piece Rattan Sectional Seating Group
Important: Retain for future reference. Read carefully.
Assembly Tools: ? (Drill recommended), ⏱️ Estimated Assembly Time: 180 minutes, ⚖️ Maximum Weight Capacity: 180 kg per seat.
Important Information
For Domestic Use Only
Usage Tips:
- Place the furniture stably on a flat floor for optimal performance.
- Install the seating units in a sheltered area, such as under an awning.
- Keep the furniture away from open flames.
- Do not hang items on the furniture structure.
- Avoid overloading the structure's anchors or weight capacity.
- It is advised not to sit on the furniture during a storm.
- Do not use the furniture in adverse weather conditions. Cover the furniture when not in use.
Precautions Before Assembly:
- Prepare a clean and dry area for assembly.
- Verify that the product is not damaged before starting.
- Check that all parts and hardware are present and accounted for.
Maintenance:
- Clean the furniture with a soft, damp cloth.
- Regularly remove any accumulated leaves or water from the fabric or cushions.
- Periodically inspect the furniture for stability and wear.
Storage Conditions:
- To prevent mold, store fabric components completely dry in a clean, dry location.
Ongoing Maintenance:
- Do not use the product if seat cloths, cushions, or tarpaulins show signs of ageing or significant wear. Contact customer service immediately if deterioration is noticed.
Caution:
- Be mindful of potential pinching or cutting hazards during the assembly process.
- The manufacturer is not responsible for damages resulting from improper installation or adverse weather conditions.
Parts List
| Part Label | Description | Quantity |
|---|---|---|
| A | Base Frame (Large Rectangular Metal Structure) | 1 |
| B | Side Panel (Vertical Metal Frame) | 1 |
| C | Back Support Frame (Metal Structure) | 1 |
| D | Armrest Support (Metal Structure) | 1 |
| E | Back Panel Support (Metal Structure) | 1 |
| F | Seat Frame Support (Metal Structure) | 1 |
| G | Cross Brace (Metal Bar) | 1 |
| H | Side Frame Connector (Metal Piece) | 2 |
| I | Base Cross Member (Metal Bar) | 2 |
| J | Top Frame Support (Metal Structure) | 1 |
| K | Side Panel Connector (Metal Piece) | 2 |
| L | Back Panel Connector (Metal Piece) | 2 |
| M | Base Frame (Square Metal Structure) | 1 |
| N | Side Panel (Vertical Metal Frame) | 2 |
| O | Back Panel (Vertical Metal Frame) | 2 |
| P | Seat Cushion | 4 |
| Q | Back Cushion | 4 |
| R | Pillow | 2 |
| S | Ottoman Lid/Seat | 1 |
Hardware List
| Hardware Label | Description | Quantity | Spare |
|---|---|---|---|
| W | M6*30 Bolt | 42 | +4 |
| X | M6*50 Bolt | 26 | +3 |
| Y | Washer | 94 | +5 |
| Z | Nut | 26 | +3 |
Assembly Instructions
Step 01: Assemble Base Frame
Attach part B (Side Panel) to part A (Base Frame). Use two M6*50 bolts (X), four washers (Y), and two nuts (Z). Insert bolts through the designated holes and secure with nuts and washers.
Step 02: Attach Back Support Frame
Attach part C (Back Support Frame) to the assembled base structure. Use six M6*50 bolts (X), twelve washers (Y), and six nuts (Z). Align holes and secure.
Step 03: Attach Armrest Support
Attach part D (Armrest Support) to the structure. Use three M6*30 bolts (W), one M6*50 bolt (X), five washers (Y), and one nut (Z). Secure all connections.
Step 04: Attach Back Panel Support
Attach part E (Back Panel Support) to the structure. Use two M6*50 bolts (X), four washers (Y), and two nuts (Z). Ensure proper alignment before tightening.
Step 05: Attach Seat Frame Support
Attach part F (Seat Frame Support) to the structure. Use six M6*50 bolts (X), twelve washers (Y), and six nuts (Z). Connect securely.
Step 06: Attach Cross Brace
Attach part G (Cross Brace) to the structure. Use three M6*30 bolts (W), one M6*50 bolt (X), five washers (Y), and one nut (Z). This likely adds rigidity.
Step 07: Attach Side Frame Connectors
Attach two parts H (Side Frame Connectors) to the structure. Use two M6*50 bolts (X), four washers (Y), and two nuts (Z) for each connector. These likely connect main frame pieces.
Step 08: Attach Base Cross Members
Attach two parts I (Base Cross Members) to the base structure. Use three M6*30 bolts (W), one M6*50 bolt (X), five washers (Y), and one nut (Z). These reinforce the base.
Step 09: Attach Top Frame Support
Attach part J (Top Frame Support) to the structure. Use two M6*50 bolts (X), four washers (Y), and two nuts (Z). This forms the top of the frame.
Step 10: Attach Side Panel Connectors
Attach two parts K (Side Panel Connectors) to the structure. Use three M6*30 bolts (W), one M6*50 bolt (X), five washers (Y), and one nut (Z) for each connector.
Step 11: Attach Back Panel Connectors
Attach two parts L (Back Panel Connectors) to the structure. Use three M6*30 bolts (W), one M6*50 bolt (X), five washers (Y), and one nut (Z) for each connector.
Step 12: Complete Main Frame Assembly
The main frame structure for a seating module is now assembled. This step visually represents the completed frame from multiple angles.
Step 13: Assemble Ottoman/Module Base
Attach part M (Square Base Frame) to the structure. Use five M6*30 bolts (W) and five washers (Y). This forms the base for an ottoman or another module.
Step 14: Attach Side Panels to Module
Attach two parts N (Side Panels) to the structure. Use three M6*30 bolts (W) and three washers (Y) for each panel. These form the sides of a module.
Step 15: Attach Back Panels to Module
Attach two parts O (Back Panels) to the structure. Use four M6*30 bolts (W) and four washers (Y) for each panel. These form the backrests of a module.
Step 16: Ottoman Lid Placement
Part S is the Ottoman Lid/Seat, shown as a separate component ready for placement.
Step 17: Attach Side Panel to Ottoman/Module
Attach part N (Side Panel) to the structure. Use five M6*30 bolts (W) and five washers (Y).
Step 18: Attach Back Panel to Ottoman/Module
Attach part O (Back Panel) to the structure. Use three M6*30 bolts (W) and three washers (Y).
Step 19: Secure Seat Cushion
Attach part P (Seat Cushion) to the assembled frame. This step likely involves securing the cushion or its supporting frame using four M6*30 bolts (W) and four washers (Y).
Step 20: Final Assembly and Cushion Placement
The final step shows the completed sectional seating group. Place the seat cushions (P), back cushions (Q), and pillows (R) onto the assembled frames. The ottoman (S) is also positioned.
