HOMCOM 837-469V80/837-469V90 Cabinet Assembly Instructions

Parts List

Hardware List

Assembly Instructions

Step 1: Prepare Panel 1

Insert Cam Bolts (A) into the pre-drilled holes on Panel 1. Ensure they are screwed in straight and fully seated, but do not overtighten.

[Diagram Description: Panel 1 with multiple Cam Bolts (A) being inserted into holes. A close-up shows a Cam Bolt (A) being screwed in correctly (checkmark ✔️) and incorrectly (cross ❌).]

Step 2: Prepare Panel 2

Insert Cam Bolts (A) into the pre-drilled holes on Panel 2. Ensure they are screwed in straight and fully seated, but do not overtighten.

[Diagram Description: Panel 2 with multiple Cam Bolts (A) being inserted into holes. A close-up shows a Cam Bolt (A) being screwed in correctly (checkmark ✔️) and incorrectly (cross ❌).]

Step 3: Prepare Panel 3

Insert Cam Bolts (A) into the pre-drilled holes on Panel 3. Ensure they are screwed in straight and fully seated, but do not overtighten.

[Diagram Description: Panel 3 with multiple Cam Bolts (A) being inserted into holes. A close-up shows a Cam Bolt (A) being screwed in correctly (checkmark ✔️) and incorrectly (cross ❌).]

Step 4: Prepare Panel 4

Attach Support Brackets (G) to one side of Panel 4 using Screws (D). Insert Cam Bolts (A) into the pre-drilled holes on the other side of Panel 4. Ensure Cam Bolts (A) are screwed in straight and fully seated.

[Diagram Description: Panel 4 shown in two configurations. On one side, Support Brackets (G) are attached with Screws (D). On the other side, Cam Bolts (A) are inserted into holes. Close-ups show correct insertion of G and A.]

Step 5: Assemble Side Panel

Attach Panel 5 (Middle Shelf) to Panel 2 (Base Panel) using Cam Locks (B), Wooden Dowels (C), and Plastic Covers (J). Insert dowels (C) into corresponding holes. Insert cam bolts from Panel 2 into the holes on Panel 5. Insert Cam Locks (B) into the large holes on Panel 5 and turn them clockwise ? to secure. Cover the cam locks with Plastic Covers (J).

[Diagram Description: Panel 5 is connected to Panel 2. Close-ups show Wooden Dowels (C) being inserted, Cam Locks (B) being inserted and turned clockwise ?, and Plastic Covers (J) being placed over Cam Locks (B).]

Step 6: Assemble Other Side Panel

Attach Panel 1 (Left Side Panel) to Panel 5 (Middle Shelf) using Cam Locks (B), Wooden Dowels (C), and Plastic Covers (J). Insert dowels (C) into corresponding holes. Insert cam bolts from Panel 5 into the holes on Panel 1. Insert Cam Locks (B) into the large holes on Panel 1 and turn them clockwise ? to secure. Cover the cam locks with Plastic Covers (J).

[Diagram Description: Panel 1 is connected to Panel 5. Close-ups show Wooden Dowels (C) being inserted, Cam Locks (B) being inserted and turned clockwise ?, and Plastic Covers (J) being placed over Cam Locks (B).]

Step 7: Attach Bottom Panel

Attach Panel 4 (Bottom Panel) to the assembled structure (Panels 1, 2, and 5) using Cam Locks (B), Wooden Dowels (C), and Plastic Covers (J). Insert dowels (C) into corresponding holes. Insert cam bolts from Panels 1, 2, and 5 into the holes on Panel 4. Insert Cam Locks (B) into the large holes on Panel 4 and turn them clockwise ? to secure. Cover the cam locks with Plastic Covers (J).

[Diagram Description: Panel 4 is attached to the base of the cabinet structure. Close-ups show Cam Locks (B) being secured and covered with Plastic Covers (J).]

Step 8: Attach Top Panel

Attach Panel 3 (Top Panel) to the assembled structure (Panels 1 and 2) using Cam Locks (B), Wooden Dowels (C), and Plastic Covers (J). Insert dowels (C) into corresponding holes. Insert cam bolts from Panels 1 and 2 into the holes on Panel 3. Insert Cam Locks (B) into the large holes on Panel 3 and turn them clockwise ? to secure. Cover the cam locks with Plastic Covers (J).

[Diagram Description: Panel 3 is attached to the top of the cabinet structure. Close-ups show Cam Locks (B) being secured and covered with Plastic Covers (J).]

Step 9: Prepare Back Panels

Apply Edge Banding Tape (K) to the edges of the two Back Panels (10). Ensure the tape is applied smoothly and adheres well.

[Diagram Description: Two Back Panels (10) are shown. Edge Banding Tape (K) is being applied along their edges.]

Step 10: Attach Back Panels

Position the two Back Panels (10) onto the back of the cabinet. Secure them in place using Nails (F) and a hammer ?. Ensure the panels are flush with the cabinet edges.

[Diagram Description: The cabinet is shown from the back. Two Back Panels (10) are being attached using Nails (F) hammered into the frame. A hammer icon ? is shown.]

Step 11: Install Shelf Supports

Insert Shelf Support Pins (H) into the desired pre-drilled holes on the inside of the side panels (1 and 2). Ensure they are firmly seated.

[Diagram Description: Inside view of the cabinet showing Shelf Support Pins (H) being inserted into holes on the side panels. A close-up shows the pin insertion.]

Step 12: Insert Shelves

Place the Shelves (9) onto the installed Shelf Support Pins (H). Ensure each shelf rests securely on all four pins.

[Diagram Description: Shelves (9) are shown being placed onto the Shelf Support Pins (H) inside the cabinet. Arrows ➡️ indicate the direction of placement.]

Step 13: Attach Hinges to Doors

Attach Hinges (E) to the Side Panels 7 (Left Door) and 8 (Right Door) using Screws (D). Ensure the hinges are oriented correctly as shown in the diagram.

[Diagram Description: Side Panel 7 and Side Panel 8 are shown with Hinges (E) being attached using Screws (D).]

Step 14: Attach Doors to Cabinet

Align the attached Hinges (E) on the doors (7 and 8) with the corresponding pre-drilled holes on the cabinet frame (Panels 1 and 2). Secure the hinges to the cabinet using Screws (D). Note: Remove any protective film from the surface of parts 1 and 3 before proceeding.

[Diagram Description: Doors (7 and 8) with attached hinges are shown being mounted onto the cabinet frame. Screws (D) are used to secure the hinges. A note indicates removing protective film from parts 1 and 3.]

Step 15: Attach Doors (Continued)

Ensure the doors (7 and 8) are correctly attached and aligned. Adjust hinges if necessary. Note: Remove any protective film from the surface of part 2 before proceeding.

[Diagram Description: The cabinet with doors attached. Close-ups show hinge attachment points. A note indicates removing protective film from part 2.]

Step 16: Secure to Wall

For safety, it is recommended to secure the cabinet to the wall using the provided Wall Anchor Straps (I) and screws. Attach one end of the strap to the cabinet and the other end to a wall stud or appropriate wall anchor.

[Diagram Description: The cabinet is shown with Wall Anchor Straps (I) being attached to the top rear of the cabinet and to a wall. Icons indicate 'Cabinet' and 'Wall'.]

Hinge Adjustment Guide

It may be necessary to adjust the hinges so that the doors align properly.

Vertical Adjustment

To adjust the door vertically, loosen the screw as shown ? and move the door up or down ⬆️⬇️ as needed. Retighten the screw.

[Diagram Description: A close-up of a hinge adjustment screw being loosened and the door being moved vertically.]

Gap Adjustment

To adjust the gap between the door and the main frame, turn the screw clockwise ? or anti-clockwise ? as needed. This adjusts the door's depth.

[Diagram Description: A close-up of a hinge adjustment screw being turned clockwise or anti-clockwise to alter the door gap.]

Lateral Adjustment

To adjust the door laterally (side-to-side), adjust the screw as shown by turning clockwise ? or anti-clockwise ?. This moves the door left or right ⬅️➡️.

[Diagram Description: A close-up of a hinge adjustment screw being turned clockwise or anti-clockwise to move the door laterally.]

Final Step: Please fix other screws. ?

[Diagram Description: A generic icon representing screws.]

Contact Information

If you have any questions or require assistance, please contact the relevant customer care center:

United States (US)

Phone: 001-877-644-9366
Email: customerservice@aosom.com
Importer: Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA
Origin: MADE IN CHINA

Canada (CA)

Phone: 416-792-6088
Email: customerservice@aosom.ca
Importer: Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9
Origin: MADE IN CHINA

Germany (DE)

Phone: +49 40 87408465
Email: service@aosom.de
Address: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany
Origin: IN CHINA HERGESTELLT

Italy (IT)

Phone: 0039-0249471447
Email: clienti@aosom.it
Importer: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI)
Origin: FATTO IN CINA

Spain (ES)

Phone: 0034-931294512
Email: atencioncliente@aosom.es
Importer: SPANISH AOSOM, S.L., C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN.
Origin: HECHO EN CHINA

Portugal (PT)

Phone: 0034-931294512
Email: info@aosom.pt
Importer: SPANISH AOSOM, S.L, C.ROC GROS N.15, 08550. ELS HOSTALETS DE BALENYÀ
Origin: FEITO NA CHINA

France (FR)

Phone: 0033-1-84166106
Email: aosom@mhfrance.fr
Importer: MH FRANCE, 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France
Origin: FABRIQUÉ EN CHINE

Recycling information: Adresses sur quefairedemesdechets.fr