Jablotron JA-110A II Bus Internal Siren with Battery Backup
Manufacturer: Jablotron
Website: www.jablotron.com
Product Overview
The JA-110A II is a component within the JABLOTRON system, designed for indoor alarm indication. It allows for the interruption of ongoing alarm indications by pressing a button on the siren, which can also confirm presence or trigger a panic alarm (optional function). The siren occupies one system position and requires installation by a trained technician with a valid certificate issued by an authorized distributor.
The document is a machine translation from the original English version. In case of uncertainty or doubt, refer to the original document. For any errors or further questions, contact technical support.
Installation Guide
Step 1: Removing the Siren Housing Use a screwdriver to press one side of the housing (1.) to detach it from the plastic frame.
Step 2: Removing the Middle Frame Part Press the four tabs indicated by arrows (2.) to remove the middle part of the frame (3.).
Step 3: Cable Routing Feed the BUS cable through the designated rectangular recess in the plastic base.
Step 4: Securing the Base Fasten the plastic base to the chosen location using screws. If the siren uses a battery, position it under the top side of the plastic base as shown in Figure 1.
Step 5: Reassembly Assemble the plastic frame with the plastic base, which will secure the battery in place.
System Assignment and Settings Refer to the control panel manual for the recommended software or application based on the control panel type.
Figure 1: Siren Removal Before Installation [Diagram showing the process of detaching the siren housing from the frame.]
Figure 2: Description of Internal Product Parts
- 1 – LED indicators
- 2 – Buttons
- 3 – Production number
- 4 – Button tabs
- 5 – Piezoelectric siren
- 6 – BUS terminal
- 7 – Tamper sensors
- 8 – Battery connector for BAT-3V2-CR2
Specifications
| Parameter | Specification |
|---|---|
| Power | From the central unit's BUS 12 V DC (8...15 V) |
| Optional backup battery | 3.2 V LiFePo4 CR2 0.4 Ah (Note: Battery not included) |
| Quiescent current for backup | 5 mA |
| Maximum current consumption during cable selection | 120 mA |
| Low battery status | 2.9 V |
| Type of warning device | Type Z/24-hour backup |
| Siren | Piezoelectric, 100 dB/m (±5 dB/m) |
| Dimensions | 80 x 80 x 35 mm |
| Weight | 92 g |
| Classification | Security class 2/Environmental class II (EN 50131-1) |
| Operating environment | Indoor general use |
| Operating temperature range | -10 °C to +40 °C |
| Average operating humidity | 75% RH, non-condensing |
| Certification body | Trezor Test sro (No. 3025) |
| Complies with | EN 50131-1, EN 50131-4, EN 50130-4, EN 55032, EN 62368-1, EN 50581 |
| Recommended screw | 2x 3.5 x 40 mm (countersunk head) |
Declarations and Compliance
CE Marking JABLOTRON a.s. hereby declares that the JA-110A II is in compliance with the relevant EU harmonisation legislation: Directive No.: 2014/35/EU, 2014/30/EU, 2011/65/EU. The original declaration of conformity can be found at www.jablotron.com – Downloads section.
UKCA Marking [UKCA Mark Symbol]
Disposal Information Note: Proper disposal of this product helps conserve valuable resources and prevent potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the retailer, or contact your local municipality for more information on the nearest collection point.
QR Code Scan the attached QR code for an electronic version of this document (available in other languages) or an installation version for JA-100.
Manufacturer Information
JABLOTRON a.s.
Pod Skalkou 4567/33
46601 Jablonec nad Nisou
Czech Republic
Tel.: +420 483 559 911
Internet: www.jablotron.com
