Assembly Instructions
LUCA TWIN DAYBED
ITEM NO: Y2103W-350/351 SKU: 314673/314674
Estimated Assembly Time: 15 min ⏱️
Required Tools: 1 x Allen Key ?
Parts List
| PART | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| A | 1992T-A-W: (White) | [Image of Back Panel] | Back | 1 |
| B | 1992T-B-W: (White) | [Image of Side Rail] | Rail | 1 |
| C | 1992T-C-W: (White) | [Image of Left End Panel] | Left End | 1 |
| D | 1992T-D-W: (White) | [Image of Right End Panel] | Right End | 1 |
| E | 1992T-E | [Image of Slats] | Slats | 1 |
Hardware List
| Part | SKU# | IMAGE | DESCRIPTION | QTY |
|---|---|---|---|---|
| 1 | 1992T-1(4) | [Image of Bolt and Nut] | Bolt and nut M8*80mm | 4 |
| 2 | 1992T-2(4) | [Image of Bolt] | Bolts M8*20mm | 4 |
| 3 | 1992T-3(4) | [Image of Dowel] | Dowel Ø8*40mm | 4 |
| 4 | 1992T-4(14) | [Image of Screw] | Screws 8#*30mm | 14 |
| 5 | 1992T-5(1) | [Image of Allen Key] | Allen key 60*22*4mm | 1 |
Important Notes & Care
Screwdriver will be prepared by yourself. ?
The hardware is located in the packing item.
NOTE: Must tighten screws periodically. With use, screws may become loose. Check tightness of all screws every 6-8 weeks.
Cleaning Instructions
After assembly, clean and polish the completed parts if necessary with a soft cloth and industrial-recognized furniture polish.
Assembly Steps
Step 1: Attach Back and Side Ends
Inserting the dowel (3) into the respective holes at Back (A).
Assemble Side End (C), (D) to Back (A) by Bolt+nut (1).
Diagram shows the Back panel (A) with two Side Ends (C and D) being attached. Dowels (3) are inserted into holes on the edges of Back (A). Bolts (1) and nuts are used to connect the Side Ends to the Back panel. A warning icon (⚠️) indicates 'Distinguishing the Ends (C), (D)'. An inset shows 'Before assembly: Move the nut out'. Quantities indicated: 1=4 Pcs, 3=4 Pcs. Tools required for this step: 2 x Person (? x 2), 1 x Allen Key (? x 1).
Step 2: Attach Rails
Attaching Bolt (5) to pre-holes on Side End (C) and (D).
Connecting the hook on Rail (B) to Bolt (5) and fasten.
Pay attention to rail orientation.
Diagram shows the partially assembled frame. Rails (B) are being attached to the Side Ends (C and D). Bolts (5) are inserted into pre-holes on the Side Ends. The hook of the Rail (B) connects to these bolts. Bolts (2) are used for fastening. An inset shows a close-up of the connection. Quantities indicated: 2=4 Pcs. Tools required for this step: 1 x Allen Key (? x 1).
Step 3: Attach Slats
Please fasten slats (E) by screw (4) into corresponding holes.
Diagram shows the daybed frame with slats (E) being placed and secured. Screws (4) are used to fasten the slats to the frame. Quantities indicated: 4=14 Pcs.
That's it! You've finished assembling your item. Thank you!
