Baby Trend Trend EZ Bouncer

Product Overview

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.

Image Description: A line drawing of the Trend EZ Bouncer.

Warranty Information

DO NOT RETURN YOUR PRODUCT TO THE STORE. PLEASE CONTACT BABY TREND® FOR REPLACEMENT PARTS, SERVICE AND REPAIR.

The Baby Trend® warranty covers workmanship defects within 1 year of purchase. Any product subjected to misuse, abuse, abnormal use, excessive wear and tear, improper assembly, negligence, environmental exposure, alteration, or accident, or with an altered or removed serial number, invalidates all claims against the manufacturer. Any damage to property during installation is the sole responsibility of the end user.

Customer Service Department can be contacted at 1 (800) 328-7363 Monday through Friday between 8:00 a.m. and 4:30 p.m. (PST). Return Authorizations are required prior to returning product(s) to Baby Trend®. Please visit http://babytrend.com/pages/limited-warranty for complete warranty details.

Safety Warnings

⚠️ WARNING! Not intended for infant sleep and should never be used for this purpose.

FALL HAZARD: Babies have suffered skull fractures falling while in and from bouncers.

• Use bouncer ONLY on floor.
• ALWAYS use restraints. Adjust to fit snugly.
• NEVER lift or carry baby in bouncer.

SUFFOCATION HAZARD: Babies have suffocated when bouncers tipped over on soft surfaces and/or when bouncers have been used as a sleep product.

• NEVER use on a bed, sofa, cushion, or other soft surface.
• Stay near and watch baby during use. This product is not safe for sleep or unsupervised use. If baby falls asleep, remove baby as soon as possible and place baby on a firm, flat sleep surface such as a crib or bassinet.

TO PREVENT FALLS AND SUFFOCATION:

• ALWAYS use restraints. Adjust to fit snugly, even when baby falls asleep.
• STOP using bouncer when baby starts trying to sit up or has reached 20 lb (9 kg), whichever comes first.

⚠️ WARNING:

• Toy bar is NOT designed to be used as a carry handle.
• NEVER use on any elevated surface.
• NEVER leave baby unattended.
• NEVER allow your bouncer to be used as a toy.
• NEVER move bouncer with the child inside.
• NEVER substitute parts.
• Bouncer is NOT intended for use as a carrier.

❗ IMPORTANT ASSEMBLY NOTES:

• Check your bouncer for loose screws, worn parts, torn material or stitching on a regular basis. Replace or repair parts as needed.
• Discontinue use of the bouncer should it malfunction or become damaged.
• Adult assembly required. Care should be taken in unpacking and assembly. Examine product frequently for damage, missing or loose parts. DO NOT use if any parts are missing, damaged or broken.
• Contact Baby Trend for replacement part and instructions if needed. Dial (800) 328-7363.

Parts List

Check that you have all the parts for this model before assembling the bouncer.

• Seat pad (Almohadilla del asiento)
• Backrest Tube (Tubo del respaldo)
• Attached 3-Way Connectors (Conector de 3 Vías Adjunto)
• Headrest (Type varies) (Apoyacabeza - Tipo varía)
• Padded Footrest Wire (Alambre del apoyapiés Acolchado)
• Rear base frame tube (Tubo posterior del armazón de la base)
• Left Base Frame Wire (Alambre izquierdo del armazón de la base)
• Right Base Frame Wire (Alambre derecho del armazón de la base)
• *Toy Bar with plush toys (Type may vary) (*Barra de juguetes con juguetes de peluche - El tipo puede variar)
• Music/Vibration Unit (Unidad de música/vibración)

Assembly Instructions

Bouncer Frame Assembly

1. Place the rear base frame tube on a flat surface and lift the plastic corners. Insert the left and right base frame wires into the rear base frame tube. Push the plastic corners back down until they snap securely onto the base frame wires. Set the assembled Base frame aside and proceed to step 2.
2. Reference the 3-Way Connector Diagram. The 3-Way Connectors will be preassembled at corner A. Place the Base frame upright on a flat surface with corners B and C of the 3-Way Connectors pointing up. The Backrest Bar has 2 square brackets with an opening for the Toy Bar. Be sure that the openings are facing up. Align the Backrest bar to corner B. Insert both ends into the 3-Way connector until they click into place.
3. DO NOT Discard the Foam Padding from the Footrest Wire.
4. To Insert the Footrest Wire, align the ends to corner C of the 3-Way Connector. Be sure the small curvature parallels with the surface and the ends of the wire both point up. Insert the ends into the 3-Way Connectors and be sure that they click into place. NOTE: The pins on the 2 Bars must click into position when inserted into the connectors correctly.
5. The completed frame assembly should look exactly as shown.
6. For safety and assurance, check that the screw on the 3-Way Connector is tightened on both sides.
7. Bouncer frame assembly is complete.

Battery Installation

The music/vibration unit requires two size C batteries (not included). It is recommended that you use alkaline batteries for longer battery life.

⚠️ CAUTION: To prevent possible battery leakage, be sure to follow the guidelines outlined below.

• Do not mix old and new batteries.
• Do not mix different types (alkaline, standard, or rechargeable).
• Keep batteries out of reach of children.
• Always dispose of batteries properly.
• Remove batteries when the bouncer is not in use for long periods of time.
• Never leave exhausted batteries in the unit.
• Never try to recharge non-rechargeable batteries.

6. Remove the battery cover using a Philips screwdriver. Install two size C batteries and replace the battery cover. Do not overtighten the screw.

Music/Vibration Unit Installation

7. Align the mounting groove on the unit to the corresponding slot on the Footrest wire. Slide the unit onto the mounting groove until it is securely in place.

Installing Seat Pad

8. Unbuckle the straps on the back of the seat pad.

9. Slide the top of the seat pad over the backrest tube.

10. Pull the front edge of the seat pad over the music/vibration unit and then pull each side of the seat pad over the footrest wire until it fits snugly over the bouncer frame. Follow the illustrated steps to cover the Music/Vibration Unit and Footrest wire. The covered bouncer should have the cover wrapped nicely all around the upper frame assembly.

Securing Seat Pad

11. Secure the seat pad to the frame by buckling the straps on the back of the pad. Place the bouncer back in the upright position.

Toy Bar Installation

12. Position the toy bar above the bouncer as shown. Insert the ends of the toy bar through the corresponding holes in the seat pad and into corresponding holes on the frame. Push in until both sides click into place. To remove, press the release clips and pull up.

Headrest Installation

13. To hook the Headrest to the Bouncer, use the adjustable hook and loop strap. Thread it from front to back through the headrest hoop. To adjust, detach and attach the hook and place it at your desired height.

Safety

Seat Restraint

14. If buckled, unbuckle the straps on each side of the seat restraint. Carefully place the child in the bouncer seat and buckle the straps. Adjust the straps so that the restraint fits the child snugly.

Care and Cleaning

15. Remove the seat pad and headrest from the frame. Ensure that all buckles on the seat pad are fastened. Do not iron. Do not dry clean.

16. Instructions:

• WASHING INSTRUCTIONS (Seat Pad / Head Rest): Machine wash on gentle delicate cycle with cold water. Do not bleach. Do not tumble dry. Hang to dry. Do not iron. Do not dry clean.
• TOY BAR AND TOYS: Wipe clean with a damp cloth and mild soap. Air dry. Do not immerse in water.
• FRAME: Wipe the metal frame with soft, clean cloth and mild soap.

Music/Vibration Unit Operation

17. To use the vibration function: Slide the vibration switch to the ON position.

18. To use the music function: Slide the music switch to LOW or HIGH to activate the music and select the volume.

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

⚠️ WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada ICES-003 Statement

This Class B digital apparatus complies with Industry Canada Standard ICES-003. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.